background image

Model 5200 Series Attic Lifts

Installation and Operation Manual

Page 1       SpaceLift 5200 Series Attic Lift Manual (10/14)

Protected by U.S. Patent No. 8,292,031.

Model Number:

Serial Number:

Installation Date:

Installer:

Place of Purchase:

Date of Purchase:

Congratulations on the purchase of your new SpaceLift 

Products 5200 Series attic lift system. Expect to receive 

many years of reliable service moving household items 

between the floors of your home. 

BEST-IN-CLASS FEATURES INCLUDE:

Low-profile design, no vertical restriction

Automated lift with 200-pound load limit

Platforms have up to 24 cubic feet capacity

Factory assembled for ease of installation 

Wall-mounted control unit with key lock

Load management system

Two-year factory warranty

5200 SERIES SPECIFICATIONS

Lift Weight Capacity: 200 lbs

Lift Speed: 3 inches per second

Max Vertical Travel: to 15 feet

Joist/Ceiling Depth: 7 to 14 inches

Platform Leveling: Variable adjustment

Power Requirement: 110 VAC – 120 VAC

Tethers: Stainless steel cable

Remote Control: Momentary up/down buttons

Model 5222

Model 5228

Dimensions (inches}:

22 W x 59.5 L x 7 H 28 W x 59.5 L x 7 H

Rough Framed Opening: 22.5 x 60 (+/- 1/8)

28.5 x 60 (+/- 1/8)

Internal Platform Area:  18 x 41

24 x 41

Ceiling Drywall Cutout: 22.5 x 46

28.5 x 46

Landing Space Area: 

24.5 x 48

30.5 x 48

Unit Weight: 

75 lbs

88 lbs

SpaceLift 5200 Series, view stowed in attic floor

SpaceLift 5200 Series, operational perspective

Summary of Contents for 5200 Series










Reviews: