![background image](http://html.mh-extra.com/html/sony/xplod-cdx-ca810x/xplod-cdx-ca810x_installation-connections_1323963001.webp)
BUS CONTROL IN
BUS AUDIO IN
Source selector
*
Sélecteur de source
*
XA-C30
*
not supplied
non fourni
Sony Corporation © 2003
Printed in Thailand
3-247-570-11
(1)
Cautions
• This unit is designed for negative ground 12 V DC
operation only.
• Do not get the wires under a screw, or caught in
moving parts (e.g. seat railing).
• Before making connections, turn the car ignition
off to avoid short circuits.
• Connect the
yellow
and
red
power input leads
only after all other leads have been connected.
•
Run all ground wires to a common ground
point.
• Be sure to insulate any loose unconnected wires
with electrical tape for safety.
• The use of optical instruments with this product
will increase eye hazard.
Notes on the power supply cord (yellow)
• When connecting this unit in combination with
other stereo components, the connected car
circuit’s rating must be higher than the sum of
each component’s fuse.
• When no car circuits are rated high enough,
connect the unit directly to the battery.
Parts Iist (
1
)
• The numbers in the list are keyed to those in the
instructions.
• The bracket
1
and the protection collar
3
are
attached to the unit before shipping. Before
mounting the unit, use the release keys
5
to
remove the bracket
1
and the protection collar
3
from the unit. For details, see “Removing the
protection collar and the bracket (
4
)” on the
reverse side of the sheet.
•
Keep the release keys
5
for future use as they
are also necessary if you remove the unit from
your car.
Caution
Handle the bracket
1
carefully to avoid injuring
your fingers.
Note
Before installing, make sure that the catches on both
sides of the bracket
1
are bent inwards 2 mm (
3
/
32
in). If
the catches are straight or bent outwards, the unit
will not be installed securely and may spring out.
Installation/Connections
Installation/Connexions
FM
/
AM
Compact Disc
Player
Connection example (
2
)
Notes (
2
-A)
• Be sure to connect the ground cord before
connecting the amplifier.
• If you connect an optional power amplifier and do
not use the built-in amplifier, the beep sound will
be deactivated.
Tip (
2
-B-
)
For connecting two or more CD/MD changers, the
source selector XA-C30 (optional) is necessary.
Connection diagram (
3
)
1
To a metal surface of the car
First connect the black ground lead, then connect
the yellow and red power input leads.
2
To the power antenna control lead or power
supply lead of antenna booster amplifier
Notes
• It is not necessary to connect this lead if there is
no power antenna or antenna booster, or with
a manually-operated telescopic antenna.
• When your car has a built-in FM/AM antenna in
the rear/side glass, see “Notes on the control
and power supply leads.”
3
To AMP REMOTE IN of an optional power
amplifier
This connection is only for amplifiers. Connecting
any other system may damage the unit.
4
To the interface cable of a car telephone
5
To the +12 V power terminal which is
energized in the accessory position of the
ignition key switch
Notes
• If there is no accessory position, connect to the
+12 V power (battery) terminal which is
energized at all times.
Be sure to connect the black ground lead to a
metal surface of the car first.
• When your car has a built-in FM/AM antenna in
the rear/side glass, see “Notes on the control
and power supply leads.”
6
To the +12 V power terminal which is
energized at all times
Be sure to connect the black ground lead to a
metal surface of the car first.
Notes on the control and power supply leads
• The power antenna control lead (blue) su12
V DC when you turn on the tuner.
• When your car has built-in FM/AM antenna in the
rear/side glass, connect the power antenna control
lead (blue) or the accessory power input lead (red)
to the power terminal of the existing antenna
booster. For details, consult your dealer.
• A power antenna without relay box cannot be used
with this unit.
2
A
B
SUB OUT (MONO)
AUDIO OUT
REAR
BUS AUDIO IN
BUS CONTROL IN
1
4
5
Equipment used in illustrations (not supplied)
Appareils utilisés dans les illustrations (non fournis)
Rear speaker
Haut-parleur arrière
Front speaker
Haut-parleur avant
1
CD/MD changer
Changeur de CD/MD
Rotary commander RM-X4S
Satellite de commande RM-X4S
Power amplifier
Amplificateur de puissance
×
4
2
×
2
3
CDX-CA810X
Active subwoofer
Caisson de graves actif
1
AUDIO OUT
FRONT
Catch