background image

SERVICE MANUAL

Sony Corporation

Published by Sony Techno Create Corporation

(US and Canadian models only)

Tuner section (AEP, Russian, UK, E (PAL),  
Saudi Arabia, Indian  and  Australian models)

FOR THE CUSTOMERS IN THE USA. NOT 
APPLICABLE IN CANADA, INCLUDING IN THE 
PROVINCE OF QUEBEC.

POUR LES CLIENTS AUX ÉTATS-UNIS. NON 
APPLICABLE AU CANADA, Y COMPRIS LA 
PROVINCE DE QUÉBEC.

AUDIO POWER SPECIFICATIONS

CEA2006 Standard
Power Output: 17 Watts RMS × 4 at 
4 Ohms < 1% THD+N
SN Ratio: 80 dBA 
(reference: 1 Watt into 4 Ohms)

Monitor section

Display type:

 Wide LCD color monitor

Dimensions:

 6.2 in

System:

 TFT active matrix

Number of pixels: 

1,152,000 pixels (800 × 3 (RGB) × 480)

Color system:

PAL/NTSC/SECAM/PAL-M automatic select

Tuner section (US, Canadian and E (NTSC) models)

FM
Tuning range:

Antenna (aerial) terminal:

External antenna (aerial) connector

Intermediate frequency:

 150 kHz

Usable sensitivity:

 10 dBf

Selectivity:

 70 dB at 400 kHz

Signal-to-noise ratio:

 70 dB (mono)

Separation at 1 kHz:

 30 dB

Frequency response:

 20 - 15,000 Hz

AM
Tuning range:

 530 – 1,710 kHz

Antenna (aerial) terminal:

External antenna (aerial) connector

Intermediate frequency:

9,267.5 kHz or 9,257.5 kHz/5 kHz

Sensitivity:

 44 μV

DVD/CD Player section

Signal-to-noise ratio:

 80 dB

Frequency response:

 20 – 20,000 Hz

Wow and flutter:

 Below measurable limit

Harmonic distortion:

 0.05%

Region code:

 Labeled on the bottom of the unit

USB Player section

Interface:

 USB (Full-speed)

Maximum current:

 1 A

Power amplifier section

Outputs:

 Speaker outputs

Speaker impedance:

 4 – 8 ohms

Maximum power output:

 55 W × 4 (at 4 ohms)

General

Outputs:

 

Video output terminal (rear)
Audio output terminals (front, rear/sub 
switchable)
Power antenna (aerial)/Power amplifier control 
terminal (REM OUT)

Inputs:

 

Illumination control terminal
Remote controller input terminal
Antenna (aerial) input terminal
Microphone input terminal
Parking brake control terminal
Reverse input terminal
Camera input terminal
AUX audio input terminal (Front)
AUX Audio/Video input terminal (Rear)
USB port

Power requirements:

 12 V DC car battery 

(negative ground (earth))

Dimensions:

 Approx. 178 mm × 101.5 mm × 169 mm 

(7 

1

/

8

 × 4 × 6 

3

/

4

 in) (w/h/d)

Mounting dimensions:
(Except AEP, Russian and UK models)

Approx. 178 mm × 100 mm × 165 mm 
(7 

1

/

8

 × 4 × 6 

1

/

2

 in) (w/h/d)

(AEP, Russian and UK models)

Approx. 182 mm × 100.6 mm × 159 mm 

Mass:

 Approx. 1.7 kg (3 lb 12 oz)

Package contents:

Parts for installation and connections (1 set)
Remote Commander (1): RM-X170
Microphone (1)

Design and specifications are subject to change 
without notice.

Region code

The region system is used to protect software 
copyrights.
The region code is located on the bottom of the 
unit, and only DVDs labeled with an identical region 
code can be played on this unit.

DVDs labeled 

can also be played.

If you try to play any other DVD, the message 
[Playback prohibited by region code.] will appear 
on the monitor screen. Depending on the DVD, no 
region code may be labeled even though playing 
the DVD is prohibited by area restrictions.

Wireless Communication

Communication System:

BLUETOOTH Standard version 3.0

Output:

 

BLUETOOTH Standard Power Class 2 (Max. +4 
dBm)

Maximum communication range:

Line of sight approx. 10 m (33 ft)*

1

Frequency band:

 

2.4 GHz band (2.4000 – 2.4835 GHz)

Modulation method:

 FHSS

Compatible BLUETOOTH Profiles*

2

:

A2DP (Advanced Audio Distribution Profile) 1.2
AVRCP (Audio Video Remote Control Profile) 1.4
HFP (Handsfree Profile) 1.6
PBAP (Phone Book Access Profile)
OPP (Object Push Profile)
SPP (Serial Port Profile)

*1 The actual range will vary depending on factors such 

as obstacles between devices, magnetic fields 
around a microwave oven, static electricity, 
reception sensitivity, antenna’s performance, 
operating system, software application, etc.

*2 BLUETOOTH standard profiles indicate the purpose 

of BLUETOOTH communication between devices.

External input terminal (E (PAL), Saudi Arabia, 
Indian and Australian models only)

FM
Tuning range:

 87.5 – 108.0 MHz

Antenna (aerial) terminal:

External antenna (aerial) connector

Intermediate frequency:

 150 kHz

Usable sensitivity:

 10 dBf

Selectivity:

 70 dB at 400 kHz

Signal-to-noise ratio:

 70 dB (mono)

Separation at 1 kHz:

 30 dB

Frequency response:

 20 - 15,000 Hz

AM
Tuning range:

 531 – 1,602 kHz

Antenna (aerial) terminal:

External antenna (aerial) connector

Intermediate frequency:

9,267 kHz or 9,258 kHz/4.5 kHz

Sensitivity:

 44 μV

 87.5 – 107.9 MHz

FM tuning step:

 100 kHz/200 kHz switchable
 (E (NTSC) model only)

(7 

1

/

4

 × 4 

3

/

8

 × 6 

3

/

8

 in) (w/h/d)

XAV-68BT

SPECIFICATIONS

AV CENTER

9-896-015-04

2015A33-1

© 

2015.01

US Model

Canadian Model

AEP Model

UK Model

E Model

Australian Model

Ver. 1.3  2015.01

Model Name Using Similar Mechanism

XAV-65

Mechanism Type

DR28N-ABB-YG

Summary of Contents for XAV-68BT

























Reviews: