background image

SPECIFICATIONS

— Continued on next page —

SERVICE MANUAL

M2000 MECHANISM

Photo : DCR-TRV238E

DCR-TRV238E/TRV239E

RMT-814

Level 1

Ver 1.2  2002. 06

DIGITAL VIDEO CAMERA RECORDER

output
connectors

S video output

4-pin mini DIN
Luminance signal: 1 Vp-p,
75 

(ohms), unbalanced

Chrominance signal: 0.3 Vp-p,
75 

(ohms), unbalanced

Audio/Video output

AV MINIJACK, 1 Vp-p, 75 

(ohms), unbalanced, sync negative
327 mV, (at output impedance more
than 47 k

(kilohms))

Output impedance with less than
2.2 k

(kilohms)/Stereo minijack

(ø 3.5 mm)

Headphone jack

Stereo minijack (ø 3.5 mm)

USB jack

mini-B

LANC jack

Stereo mini-minijack (

ø 2.5 mm)

MIC jack

Stereo minijack (ø 3.5 mm)

DV output

4-pin connector

LCD screen

Picture

6.2 cm (2.5 type)
50.3 

×

37.4  mm (2 

×

 1 1/2 in.)

Total dot number

For European models:
123 200 (560 

×

 220)

Video camera
recorder

System

Video recording system

2 rotary heads
Helical scanning  system

Audio recording system

Rotary heads, PCM system
Quantization: 12 bits (Fs 32 kHz,
stereo 1, stereo 2), 16 bits
(Fs 48 kHz, stereo)

Video signal

PAL colour, CCIR standards

Recommended cassette

Hi8/Digital8 video cassette

Recording/playback time (using
90 min. Hi8 video cassette)

SP mode: 1 hour
LP mode: 1 hour and 30 minutes

Fast-forward/rewind time (using
90 min. Hi8 video cassette)

Approx. 5 min.

Viewfinder

Electric Viewfinder, Monochrome

Image device

3 mm (1/6 type CCD)
(Charge Coupled Device)
Gross: Approx. 800 000 pixels
Effective: Approx. 400 000 pixels

Lens

Combined power zoom lens
Filter diameter 37 mm (1 1/2 in.)
DCR-TRV238E:
25

×

 (Optical), 700

×

DCR-TRV239E:
25

×

 (Optical), 800

×

(Digital)

(Digital)

Focal length

2.4 – 60 mm (1/8 – 2 3/8 in.)
When converted to a 35 mm still
camera
46 – 1 150 mm (1 13/16 – 45 3/8 in.)

Colour temperature

Auto

Minimum illumination

6 lx (lux) (F 1.6)
0 lx (lux) (in the NightShot mode)*
* Objects unable to be seen due to

the dark can be shot with infrared
lighting.

General

Power requirements

7.2 V (battery pack)
8.4 V (AC power adaptor)

Average power consumption
(when using the battery pack)

During camera recording using
LCD
3.8 W
Viewfinder
3.0 W

Operating temperature

0

°

C to 40

°

C (32

°

F to 104

°

F)

Recommended charging
temperature

10

°

C to 30

°

C (50

°

F to 86

°

F)

Storage temperature

–20

°

C to + 60

°

C (–4

°

F to + 140

°

F)

Dimensions (approx.)

206 

×

 101 

×

 85 mm

(8 1/8 

×

 4 

×

 3 3/8 in.)

(w/h/d)

Mass (approx.)

890 g (1 lb 15 oz)
excluding the battery pack, cassette,
lens cap and shoulder strap
DCR-TRV238E:
1 030 g (2 lb 4 oz)
DCR-TRV239E:
1 040 g (2 lb 4 oz)
including the battery pack
NP-FM30, NP-FM50, 90min. Hi8 cassette, lens
cap and shoulder strap

Supplied accessories

See page 3.

Camera mode:
48 – 720 mm (1 15/16  – 28 3/8 in.)
Memory mode:
40 – 600 mm (1 5/8  – 23 5/8 in.)

2. GENERAL will be issued shortly.

AEP Model

East European Model

DCR-TRV238E/TRV239E

UK Model

North European Model

Russian Model

DCR-TRV238E

Содержание Handycam Digital8 DCR-TRV238E






























Отзывы: