background image

CENTRALIS UNO RTS 

is an individual control system for AC motor dedicated to roller shutters

and interior blind applications.

CENTRALIS UNO RTS 

has an integrated radio receiver compatible with the RT and RTS

transmitters allowing individual, group and master commands. Up to twelve controls can be
recorded in the 

CENTRALIS UNO RTS 

memory.

The commands coming from the radio controls can be disabled thanks to the 0/auto switch.

One or two intermediate positions can be programmed.

Compatible with sensor 

(sun protection functionning only) 

Up to three sensors can be recorded.

inteo

CENTRALIS UNO RTS

INSTALLATION

guide

Ref.9007504D 

80 mm

80 mm

33 mm 17 mm

• Main supply : 220-240V 50Hz.

• Class II product 

• Protection index IP40.

• Output : 250V~ 3A

• Output temporisation : activ for 180s.

• Environmental conditions for use : 

- temperature 0°C to +40°C (no condensation allowed).
- pollution degree typical for usual living space.

We reserve the right to make changes due to technical improvements. 

1

CENTRALIS uno RTS

FRONT PLATE

CONTROL UNIT

FRAME

BRACKET

WALL

1

Characteristics

2

Installation

The range of radio control is limited by laws regulating
radio devices and by building design. 

When planning, please ensure that there is adequate
radio reception.

In order not to affect quality of reception, a minimum
distance of 30 cm between a 

CENTRALIS uno RTS

and a radio transmitter should be maintained.

CENTRALIS uno RTS

should not be installed in the

immediate vicinity of metal surfaces. Powerful local
transmitter equipment (e.g. cordless headphones) with a
transmission frequency identical to the 

CENTRALIS

uno RTS

can affect its function.

Hereby, SOMFY, declares that this equipment
is in compliance with the essential require-
ments and other relevant provisions of
Directive 1999/5/EC. 
A Declaration of Conformity is available at the
web address 

www.somfy.com

Heading 

CE

We reserve the right to make changes due to technical improvements. 

CENTRALIS uno RTS

4

Nothing works: 

Check the motor.

Check the power supply.

Check the battery of the transmitter.

Check that the transmitter has been properly
recorded in the CENTRALIS uno RTS’s memory.

Check for any other possible source of radio
interferences.

Phantom intermediate position: 

The programmed IP can only be reached from the

UP or DOWN limits. not when the shutter is in ano-
ther position.

Lost in your programming mode: 

Just make a complete reset and start again
(refer to section 5).

6

Trouble shooting guide

This device must be installed and programmed by qualified installers for whom this instruction is inten-
ded.

Before connecting the unit, read the instructions carefully.

SOMFY SAS, capital 20.000.000 Euros, RCS Bonneville 303.970.230 

Assembly

2.1

Set the blind to its DOWN limit before programming in order to always have the same adjustment.

Programming the 2nd intermediate position 

(IP2)

b

• Move the shutter/blind at its 

DOWN

limit with the 

button and immedia-

tely press the 

button briefly.

• Press the 

and 

button simulta-

neously until the shutter/blind begins
to move 

DOWN

.

• Stop the shutter/blind at the inter-
mediate position you wish. 
If necessary, adjust this position with
the 

or 

buttons.

• Press the 

button more than 5 sec.

The shutter/blind jogs briefly

(UP/DOWN), the 2nd intermediate posi-
tion is recorded.

after 

3 seconds

STOP

IP2

2

1

3

4

5 sec.

DOWN

Operating

c

• Press briefly the 

button while the blind is

at its 

UP limit

.

The shutter/blind will move down and stop

at the 1st intermediate position.

1st intermediate position

IP1

UP limit

• Press briefly the 

button while the blind is at

its 

DOWN limit

.

The shutter/blind will move up and stop at the

2nd intermediate position.

2nd intermediate position

IP2

DOWN limit

If you record a new IP, this will automatically erase the previous one.
If you want to erase without recording a new one, Press briefly on the

button to reach the IP, then: 

To erase the 1st intermediate position, press 

■ 

button for more than 5 seconds.

To erase the 2nd intermediate position, press 

button for more than 5 seconds.

The shutter/blind jogs briefly (UP/DOWN) indicating that 

CENTRALIS uno RTS 

has deleted the intermediate position.

Delete the intermediate position

d

5

Complete reset

To completely reset the CENTRALIS uno RTS, press its PROG button for more than 7 seconds.
This will erase all of the programmed controls, the intermediate positions.

The shutter/blind jogs twice (UP/DOWN), the memory of the CENTRALIS uno RTS is cleared.

P

R

O

G

7 sec.

centralis uno RTS_9007504D  30/08/06  17:17  Page 1

Reviews: