• Tighten the nuts carefully.
IMPORTANT! Do not overtighten the nuts,
breakage and chipping of vitreous china
can occur.
• Cut 1/4” or more over the top of the nut.
• Attach the bolt caps.
IMPORTANT! Product damage can occur if
using a saw blade to cut off the excess
T-bolt length. Make sure vitreous china is
protected and covered.
3. COMPleTINg The INsTAllATION
• Flush valve should be installed to manufacturer’s
installation instructions.
• Turn on water supply valve.
• Install water closet seat (not included).
• Place and press in new wax seal around the water
closet bottom outlet.
• Install new 5/16” T-bolts.
2. INsTAllINg New wATeR ClOseT
• Check rough-in dimensions and install or relocate
flush valve and outlet as indicated.
• Record model number for reference.
• Take out the temporary rag (if used) from the water
closet flange hole.
• Carefully align and lower the water closet over the
flange and T-bolts.
IMPORTANT! Do not lift or rock the water closet
after replacement. The watertight seal will have
to be replaced if breakage occurs.
The RIghT ChOICe
We thank you for your purchase.
Our products are 100% tested but should you have
any questions, please contact us by phone or at our
web site.
Water Closet Installation Instructions
Model ST-2309-A Junior Toilet
1. ReMOvAl Of exIsTINg wATeR ClOseT
• Turn off the water supply.
• Disconnect the flush valve.
• Remove the existing water closet.
• Using putty knife, completely
remove old wax seal from floor
and bottom of water closet.
• Lay water closet down on
padded surface to help protect
the vitreous china.
wARNINg: hazardous gases
can escape through the closet flange
if new water closet is not installed quickly.
A temporary fix: place a large rag in the
closet flange.
wARNINg: Any vitreous china can chip or
break if the bolts or nuts are over-tightened
or if mishandled.
befORe yOu sTART…
• Check all local plumbing and building codes.
• Check for any damage to the new water closet
before installation.
whAT yOu wIll NeeD…
• Putty knife
• Sponge
• Safety glasses
• 10” adjustable wrench
• Measuring tape
• Large level
• Spud wrench
• Wax seal
NOTe: Plumbing system Requirements
√ Minimum flowing Pressure: 25 PsI
√ Minimum flow Rate: 18 gPM
Anillo
de cera
anterior
Cubra con tela
Old
wax ring
Cover with rag
• Flush water closet a few times and check all
connections for water seepage.
• Check for leaks.
The information contained in this document is subject to change
without notice.
10500 Seymour Avenue
Franklin Park, IL 60131
Phone: 1-800-9982-5839
Fax: 1-800-447-8329
www.sloanvalve.com
© 2013 Sloan Valve Company
Code No. 0816397 – Rev. 1 (03/13)
5”
(127 mm)
10” or 12”
(254 mm or
305 mm)
10¾”
(273 mm)
27”
(686 mm)
13
”
(330 mm)
30”
(762 mm)
FINISHED
W
ALL
FINISHED FLOOR
1 ½”
(38 mm)
5” or 7”
(127 mm or 178 mm)
CL OF OUTLET
CL OF WASTE
17½”
(445 mm)
13”
(330 mm)
10”
(254 mm)
11-1/4”
(286 mm)
5½”
(140 mm)
To maximize The performance of your Sloan WaTer cloSeT, uSe only Sloan fluShomeTerS
Efficiency Series
* HET does not apply to 1.6 gpf/6.0 Lpf flush volume.
• To seal, apply your full body weight around the
water closet.
• Place the plastic cap in the position indicated on
cap as marked.
• The metal washers and nuts can now be placed on
the bolt cap base and T-bolts.
CARe AND CleANINg Of vITReOus ChINA
Clean water closet with a cleaner safe for vitreous
china such as Sloan’s Waterfree Urinal Cleaner/
Deodorizer. Spray and wipe clean using soft cloth. Soft
abrasive cleaners may be used to remove stains.
lIMITeD wARRANTy
Unless otherwise noted, Sloan Valve Company
warrants its products, manufactured and sold for
commercial or industrial uses, to be free from defects
of material and workmanship for a period of three
(3) years (one year for SF faucets, special finish and
PWT electronics and 30 days on PWT software) from
the date of first purchase. During this period, Sloan
Valve Company will, at its option, repair, replace, or
refund the purchase price of any produce which fails
to confom with this warranty under normal use and
service. This shall be the sole and exclusive remedy
under this warranty. Products must be returned to
Sloan Valve Company, at customer’s cost. No claims
will be be allowed for labor, transportation or other
costs. This warranty extends only to persons or
organizations that purchase Sloan Valve Company’s
products directly from Sloan Valve Company for
purpose of resale. This warranty does not cover the
life of batteries.
TheRe ARe NO wARRANTIes whICh
exTeND beyOND The DesCRIPTION ON
The fACe heReOf. IN NO eveNT Is slOAN
vAlve COMPANy ResPONsIble fOR ANy
CONseQueNTIAl DAMAges Of ANy MeAsuRe
whATsOeveR.
NOTE: IN NO EVENT SHALL THE SLOAN VALVE
COMPANY BE LIABLE FOR INCIDENTAL DAMAGES,
RESULTING FROM IMPROPER INSTALLATION, OR
FOR DAMAGES CAUSED BY NEGLECT, ABUSE
OR ALTERATION.
