instructions for
angle grinders 115mm 600/860W 230V
model no:
s0530.V2 & s0685.V2
Thank you for purchasing a sealey product. manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. saFeTY
1.1.
eleCTriCal saFeTY
Warning!
it is the user’s responsibility to check the following:
check all electrical equipment and appliances to ensure that they are safe before using. inspect power supply leads, plugs and all
electrical connections for wear and damage. sealey recommend that an rcd (residual current device) is used with all electrical
products. You may obtain an rcd by contacting your local sealey dealer.
if the grinder is used in the course of business duties, it must be maintained in a safe condition and routinely PAt (Portable Appliance
test) tested.
electrical safety information, it is important that the following information is read and understood.
1.2.
ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
1.3.
regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
1.4.
important
: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fitted with the correct
fuse - see fuse rating in these instructions.
8
dO nOT
pull or carry the appliance by the power cable.
8
dO nOT
pull the plug from the socket by the cable. Remove the plug from the socket by maintaining a firm grip on the plug.
8
dO nOT
use worn or damaged cables, plugs or connectors. ensure that any faulty item is repaired or replaced immediately by a
qualified electrician.
1.5.
This product is fitted with a BS1363/A 13 Amp 3 pin plug.
if the cable or plug is damaged during use, switch the electricity supply and remove from use.
Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact a qualified electrician.
class ii products are wired with live (brown) and neutral (blue) only are marked with the class ii symbol;
A) Connect the BROWN live wire to the live terminal ‘L’.
B) Connect the BLUE neutral wire to the neutral terminal ‘N’.
c) After wiring, check that there are no bare wires and ensure that all wires have been correctly
connected.
ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.
8
dO nOT
connect either wire to the earth terminal.
Sealey recommend that repairs are carried out by a qualified electrician.
1.2.
general saFeTY
9
disconnect the grinder from the mains power before changing accessories, servicing or performing any maintenance.
9
maintain grinder and discs in good condition. check moving parts and alignment. if necessary use an authorised service agent.
9
replace or repair damaged parts.
Use recommended parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
Warning!
Always work with the grinder safety guard in place.
9
Wear approved safety goggles, ear defenders, gloves and, if grinder generates dust, a dust mask.
9
the grinding wheel or disc must only be changed by persons holding an appropriate grinding wheel certificate.
9
remove ill fitting clothing. remove ties, watches, rings and other loose jewellery and contain long hair.
9
use grinder in a suitable work area. Keep area clean, tidy and free from unrelated materials and ensure adequate lighting.
9
maintain correct balance and footing,
dO nOT
over-reach. ensure the floor is not slippery and wear non-slip shoes.
9
use only approved grinding discs and only use the normal grinding surface.
9
Check grinding disc to ensure there are no splits, cracks or other damage (see Section 6). If in doubt do not use the disc.
9
Grinding discs must be securely attached before use, but not over-tightened.
9
secure unstable workpiece with a clamp, vice or other adequate holding device and ensure the grinder is gripped with both hands.
9
Keep non-essential persons away from the working area, use screens if necessary.
8
dO nOT
operate the grinder if any parts are missing or the grinder is damaged.
8
dO nOT
use the grinder for a task it is not designed to perform.
8
dO nOT
operate the grinder where there are flammable solids, liquids or gasses.
Warning! dO nOT
grind any materials containing asbestos.
8
dO nOT
get the grinder wet or use in damp or wet locations.
8
dO nOT
switch the grinder on whilst the disc is in contact with the workpiece.
8
dO nOT
cover the grinder air vents. to do so will overheat the machine.
8
dO nOT
touch the workpiece immediately after grinding, it will be very hot.
s
0530.V2, S0685.V2 | Issue 3(D) 04/01/17
Original Language Version
© Jack sealey limited
refer to
instruction
manual
Wear ear
protection
Wear eye
protection
Wear
protective
gloves
Wear
protective
clothing
Wear a
mask
recommended fuse rating
13 Amp
