background image

1/15

SCM800 -- Eight-Channel Microphone Mixer

IMPORTANT SAFETY INSTRUCTIONS

1. READ these instructions.

2. KEEP these instructions.

3. HEED all warnings.

4. FOLLOW all instructions.

5. DO NOT use this apparatus near water.

6. CLEAN ONLY with dry cloth.

7.

DO NOT block any ventilation openings. Allow sufficient distances for adequate ventilation and install in accor­

dance with the manufacturer’s instructions.

8.

DO NOT install near any heat sources such as open flames, radiators, heat registers, stoves, or other appara­

tus (including amplifiers) that produce heat. Do not place any open flame sources on the product.

9. DO NOT defeat the safety purpose of the polarized or grounding type plug. A polarized plug has two blades 

with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wider 

blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an 

electrician for replacement of the obsolete outlet.

10. PROTECT the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, 

and the point where they exit from the apparatus.

11. ONLY USE attachments/accessories specified by the manufacturer.

12. USE only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. 

When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13. UNPLUG this apparatus during lightning storms or when unused for long periods of time.

14.

REFER all servicing to qualified service personnel. Servicing is required when the apparatus has been dam­

aged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen 

into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has 

been dropped.

15.

DO NOT expose the apparatus to dripping and splashing. DO NOT put objects filled with liquids, such as vas­

es, on the apparatus.

16. The MAINS plug or an appliance coupler shall remain readily operable.

17. The airborne noise of the Apparatus does not exceed 70dB (A).

18. Apparatus with CLASS I construction shall be connected to a MAINS socket outlet with a protective earthing 

connection.

19. To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.

20. Do not attempt to modify this product. Doing so could result in personal injury and/or product failure.

Summary of Contents for SCM800
















Reviews: