SENAO SN356, Quick Installation Manual

Page: 1 / 2

A. Base Unit
Please set up the base unit according to the following steps.
(1) Install the telescopic antenna of the
base unit and extend it fully and
vertically.
(2) Plug in the SENAO AC
adaptor to DC IN jack.
(2) (5) (4)
(3) Plug the AC adaptor into
supporting wall outlet.
(5) A standard telephone
may also be plugged into
TEL jack.
( 3 )
B. Handset
To install battery pack:
Installation
(4)
Insert
the included
telephone line into
the LINE jack and
also the telephone
line into a wall jack.
Handset Operation
B. Making a Telephone number:
1. Press phone number.
2. Enter phone number .
On incoming calls, the ringer will ring or vibrate unless the ringer
1. If the handset is on charger cradle, lift the handset to pick up the
incoming call.
2. If the handset is not on charger cradle, press any key to answer
the incoming call except .
3. If you do not take the incoming calls, the display will prompt you
have missed.
Note: While receiving incoming calls, you can mute the ring by
pressing key.
You can end a call by pressing or by placing the handset onto
the charger cradle.
1.You can use the up Arrow key to scroll through the last 10 phone
numbers dialed. Select and press .
2. Press , then press OPTION Left soft key redialing the last call.
1. Paging the base from the handset:
Press the key on the handset and then press Base (left soft key)
to establish intercom.
When the receiving party’s voice is heard at the base, answer throug
the built in microphone.
2. Paging the handset from the base:
Press the key to establish the intercom.
Press any key on the handset except to answer page.
3. Paging the handset from another handset:
This has to be done throuth the walkie-talkie mode. Please refer
to the section. Walkie-Talkie Between Handsets.
1. Press the key followed by the 2 digit unique handset ID to
establish contact..
( )
C. Answering incoming Calls:
D D. Disconnecting calls:
E. Redial:
G. Intercom:
H. Walkie-Talkie between handsets:
1 2 3
Quick Installation Guide
1.
1.press key, it Means paging all handsets.
To stop paging, press again.
2.To accept a page, press any key except or remove from
the charger if handset is locked.
3.To end the intercom, press key or place the handset back
onto the Charger.
Paging the handset from the base unit
Base Operation
A. Intercom function
MAIN MENU
1. Keypad Settings
2. Call Memory
3. Ring Setting
4. Parameter
5. Phone Setting
6. Caller ID
1. Area Code
2. +Country Code
3. Call Waiting
4. Direct Incoming
3. Language Settings
2. Base Registration
1. Customer Name Edit
7. TonePulse Select Settings
6. Restore Factory Settings
5. Back Light Settings
4. Flash Time
3. Voice Scramble
2. Battery Saving
1. LCD Contrast Settings
5. Group Ring Setting
4. Ring Volume
3. Page Tone
2. Ring Tone
1. Ring Alert Settings
2. Dialed Calls
1. Received Calls
1. Keypad Guard Settings
2. Keypad Volume
SN356
2. The call in progress will be put on hold.
3. You may press and release the PTT key at any time to establish
contact with a separate handset.
4. You can press the and then * key to communicate to all of
the other handsets.
5. The base unit can join the conversation with the 2 other handsets
by pressing the key. By pressing the key again cancels
the group conference.
6. During the group conference, the multi-Talk indicator on the base
unit will be turned on.
Intercom
Intercom