background image

 

IN0020

 Revision 05

 004799

 – 1 of 8 

POWER       PERFORMANCE      PASSION 

Installation Notes 

SP PRO Grid Fail - Generator Backup Kit 

Installation Note 

Introduction 

This installation note details the addition of the Grid fail-Generator backup kit to the SP PRO 

inverter.  The kit is only suitable for the small range (SPMC) of SP PRO AU or GO series (Series 
II) in a single phase or a three phase Advanced Multiphase Solar Hybrid installation. 

 

NOTE

Three kits are required for a three phase Advanced Multiphase Solar Hybrid installation.

 

 

The Grid fail - Generator Backup ONLY operates with Auto Start generators and CANNNOT BE 

USED with manual start generators. A three phase generator must be used in a three phase 

installation.

 

 

When the Grid fail-Generator backup kit is installed into the SP PRO, the system allows for the 
connection of an auto start backup generator that is automatically started and stopped by the 

SP PRO as required during a grid outage. 

  

SP PRO Models 

Grid fail – Generator backup 

kit, single phase. 

Grid fail – Generator backup 

kits, three phase. 

SPMC 240-AU,  004723 

1 off SPMCA-GFGB-2448,  005268  3 off SPMCA-GFGB-2448,   005268 

SPMC 241-AU,  004724 
SPMC 481-AU,  004725 
SPMC 482-AU,  004726 
SPMC 1201-AU, 004722  No Kit Available 

No Kit Available 

Preparation

 

 

When installing a single phase system, make sure one Grid Fail Generator Backup kit (005268) is 
on site. 

 

When installing a three phase Advanced Multiphase system, make sure three Grid Fail Generator 
Backup kits (3 x 005268) are on site. 
-

 

If installing a three phase system, make sure the AMP Three Phase kit is on site 
(Order code 005304) 

 

This document needs to be read in conjunction with the SP PRO Instruction Manual and SP LINK 
instruction manual (both found in SP LINK Help menu) 
 

Additional information 

Selectronic web site – 

http://www.selectronic.com.au

 or contact the Selectronic Sales Team 

 

This document applies for SP PRO Series II Rev 21 and above  

Summary of Contents for SP PRO SPMC 1201-AU









Reviews: