![background image](http://html.mh-extra.com/html/sealey/yc10b-v3/yc10b-v3_user-manual_1226143001.webp)
10TONNE BENCH ‘C’ TYPE HYDRAULIC
PRESS
MODEL NO:
YC10B.V3
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
I
MP
PO
R
RTA
TANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
TH
HE
P
PR
O
ODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PE
ER
S
SON
NAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
Familiarise yourself with the applications, limitations and hazards of the press.
Maintain the press in good condition (use an authorised service agent).
Replace or repair damaged parts. Use recommended parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
Keep the press clean for best and safest performance.
Locate the press in an adequate working area for its function, keep area clean and tidy and free from unrelated materials and ensure
there is adequate lighting.
Ensure the workpiece is correctly secured before operating the press.
Ensure that all fittings are tight before each use.
Remove ill fitting clothing. Remove ties, watches, rings, other loose jewellery and contain long hair.
Keep hands and body clear of the table when operating the press.
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
Keep children and unauthorised persons away from the working area.
Securely attach the press to a flat, firm, level surface capable of supporting the weight of press and any workpiece taking into account
clearance for workpieces.
When not in use, release pressure from the hydraulic unit and clean the press. Stand or store the arbor plates in a safe location.
DO NOT
operate the press if any parts are missing as this may cause failure and/or possible personal injury.
DO NOT
use the press for a task it is not designed to perform.
DO NOT
make any modifications to the press.
DO NOT
exceed the rated capacity of the press.
DO NOT
apply off-centre loads.
DO NOT
allow the workpiece or the arbor plates to fall from the table.
DO NOT
get the press wet or use in damp or wet locations or areas where there is condensation.
DO NOT
operate the press when you are tired or under the influence of alcohol, drugs or intoxicating medication.
DO NOT
climb upon the press.
DO NOT
use the press to compress a spring or any other item that could disengage and cause a potential hazard including personal
injury.
DO NOT
stand directly in front of a loaded press and never leave a loaded press unattended.
DO NOT
allow untrained persons to operate the press.
WARNING!
Always wear approved eye or face protection when operating the press. A full range of personal safety equipment is
available from your Sealey stockist.
WARNING:
DO
NOT
top up hydraulic unit with brake fluid, or any other fluid other than a good quality hydraulic oil (Sealey Part
Number: HJO500MLS/HJO5LS) as this may cause serious damage to the hydraulic unit and will invalidate the warranty.
WARNING!
Always position the press against a wall. If the press is situated in the open workshop, it is essential that a guard
be placed at the rear of the unit. This will prevent injury to bystanders in the event of the work piece ejecting suddenly.
WARNING!
The warnings, cautions and instructions in this manual cannot cover all possible conditions and situations that may
occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this
product, but must be applied by the operator.
▲
DANGER!
The press heavy. If it requires moving after assembly or for relocation, seek assistance from another person.
2. INTRODUCTION
High quality industrial press ideal for pressing, bending and extruding. Detachable pump and ram allow hydraulics to be used for other
purposes when press is not in use. The C-frame design provides easy-access to die from three sides, as well as permitting loading and
unloading of wide and irregular workpieces. Supplied with
fl
at pressing plates and extension tubes.
YC10B.V3 Issue 1 14/06/21
Original Language Version
© Jack Sealey Limited
Refer to
instructions
Wear eye
protection
Wear protective
gloves
Wear safety
footwear
Wear protective
clothing
Warning:
Crushing of
hands