VACUUM OIL & FLUID EXTRACTOR
& DIsChARgE 6LTR & 18LTR
model no’S:
TP6905.V2, TP6906.V2
Thank you for purchasing a sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. sAFETY
WARNINg!
ensure Health & Safety, local authority, and general workshop practice regulations are strictly adhered to when using this
equipment.
IMPORTANT!
ensure that you wear protective clothing, gloves, goggles, face mask as appropriate for the fluid being extracted.
9
Keep the extractor clean and maintain it in good condition (use an authorised service agent).
9
Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
9
Check extractor connections and fittings before use. When the unit is in use check that there are no leaks.
9
ensure that the extractor’s tank capacity exceeds the amount of fluid to be collected.
9
ensure that the end of the suction tube is fully submerged in the fluid before operating.
9
When not in use store in a safe, dry, childproof area.
9
Keep the work area clean, uncluttered and ensure there is adequate lighting.
9
maintain correct balance and footing. ensure the floor is not slippery and wear non-slip shoes.
9
Keep children and unauthorised persons away from the working area.
9
dispose of waste fluids in accordance with local authority regulations.
WARNINg! DO NOT
allow uncontrolled discharge of fluids thus polluting the environment.
9
Use only to extract engine or transmission oils, or similar non-corrosive fluids. Unit may also be used for the transfer of water.
8
DO NOT
use to extract hazardous or harmful chemicals, solvents, petrol, diesel, kerosene, alkaline or acids. If by chance such fluids
are used in the unit, it must be immediately drained and thoroughly cleaned. Use with prohibited fluids will invalidate your warranty.
8
DO NOT
store fluids in the extractor’s tank. After extracting fluid, it must be emptied into an approved receptacle as soon as possible.
8
DO NOT
dismantle, tamper or adapt the extractor for any purpose other than for which it is designed.
8
DO NOT
store in areas of high temperature, direct sunlight, rain or snow.
8
DO NOT
connect these units to an air compressor.
8
DO NOT
dismantle these units.
8
DO NOT
leave these units in a pressurised state.
WARNINg!
When the extractor’s tank contains liquid that is under pressure
DO NOT
remove or insert the extension tube connector into
the inlet/outlet fitting as this may result in a sudden discharge of liquid that could be dangerous.
9
Always press the pressure relief button before connecting or disconnecting the extension tube.
2.
i
INTRODUCTION
6ltr (TP6905) or 18ltr (TP6906) capacity device constructed from composite materials and suitable for extraction of all types of engine,
transmission and lubricating oils from cars, motorcycles, marine engines, stationary engines and industrial machinery. Features a
controlled discharge function for emptying the unit. Suitable also for low viscosity fluids such as water. Supplied with Ø5.8, Ø6.7mm
suction probes and a 1.1m extension tube. Uses probes to drain engine oil through the dipstick hole. Also suitable for draining fish tanks,
basins and sinks.
3.
i
sPECIFICATION
Original Language Version
© Jack Sealey limited
Refer to
instruction
manual
Wear protective
gloves
Wear face
shield
Wear protective
clothing
Model No:
TP6905
TP6906
Capacity
6ltr
18ltr
Suction probes Ø5.8 x 870mm, Ø6.7 x 870mm
Ø5.8 x 870mm, Ø6.7 x 870mm
extension tube Ø9.8 x 1010mm
Ø9.8 x 1010mm,
Weight
3kg
5.6kg
TP6905
TP6906
TP6905.V2, TP6906.V2 Issue:3 (3) 26/04/19
