20V 1/2”SQ DRIVE IMPACT WRENCH 230NM -
BODY ONLY
MODEL NO:
CP20VIW
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
1.1.
GENERAL SAFETY.
9
Maintain the Impact Wrench and battery in good condition. Check moving parts alignment on a regular basis.
9
Replace or repair damaged parts. Use an authorised service agent and recommended parts only. Unauthorised parts may be
dangerous and will invalidate the warranty.
9
Ensure the Impact Wrench is switched off before installing the battery pack.
9
Keep the Impact Wrench and charger clean for best and safest performance.
9
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain long hair.
9
Evaluate your working area before using the Impact Wrench; e.g. ceilings, floors and enclosures may contain electrical items or
water piping
9
Ensure battery pack is correctly inserted into the Impact Wrench handle and latched in place before attempting to switch on Impact
Wrench.
9
Secure loose work pieces with a clamp, vice or other adequate holding device.
9
Avoid unintentional starting.
9
Wear approved safety eye protection (standard spectacles are not adequate).
9
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-skid shoes.
9
Keep direction switch in the locked position until the Impact Wrench
is required for use.
9
Keep children and unauthorised persons away from the working area.
8
DO NOT
use the Impact Wrench where there are flammable liquids, solids or gases, such as paint solvents, etc.
8
DO NOT
allow children to operate the Impact Wrench.
8
DO NOT
operate the Impact Wrench
if any parts are missing as this may cause failure and/or personal injury.
8
DO NOT
hold unsecured work piece in your hand.
8
DO NOT
leave the Impact Wrench operating unattended.
8
DO NOT
carry the Impact Wrench with your finger on the power switch. Keep direction switch in the locked position.
8
DO NOT
use the Impact Wrench for a task it is not designed to perform.
8
DO NOT
operate the Impact Wrench
when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
DO NOT
get the Impact Wrench or battery charger wet or use in damp or wet locations.
2. INTRODUCTION
P
owerful, lightweight cordless impact wrench. Durable composite housing with soft grip for added comfort. Produces torque of up to 230Nm.
Variable speed trigger switch for easy control. Built-in LED work light. Forward, reverse and trigger-lock. Fitted with electronic brake. Supplied
with belt hook for safer storage whilst not in use. Requires compatible 20V battery and mains charger, sold separately.
3. SPECIFICATION
Model No.. ..............................................................
CP20VIW
Battery ...................
20V 2Ah - 6Ah Lithium-ion (not included)
Consumable parts:
C
P20VBP2 - 2Ah Battery
C
P20VBP4 - 4Ah Battery
C
P20VBP6 - 6Ah Battery
Drive .........................................................................
1/2” Sq.
Impact rate ...........................................................
0-3000bpm
No load Speed ......................................................
0-2200rpm
M
aximum Torque
.........................................................
230Nm
Replacement parts
..............................
CP20VMC - mains charger (not included)
Vibration/uncertainty ................................. 15.87m/s²/1.5m/s²
Uncertainty ................................................................. 1.5m/s²
C
P20VIW Issue 2 (2) 13/05/21
Original Language Version
© Jack Sealey Limited
Refer to
instructions
Wear eye
protection
Wear protective
gloves
Wear ear
protection
fig.1
