WARNING! DO NOT
use the wrench if damaged or thought to be
faulty.
Ensure all workshop safety rules, regulations and conditions are
complied with when using this wrench.
Maintain correct balance and footing. Ensure the floor is not
slippery and wear steel toe-capped non-slip shoes / boots.
Always wear eye protection when using the wrench.
Keep children and unauthorised persons away from the working
area.
Ensure that all hand tools, sockets and extensions are not
damaged, use of such items may result in personal injury.
Apply the torque slowly and grip the centre of the handle.
DO NOT
apply load to the end of the handle.
DO NOT
subject the wrench to excessive force or shocks.
DO NOT
use the wrench to break fasteners.
DO NOT
use the wrench as a hammer or lever bar.
DO NOT
use extensions on the handle as this may result in
damage to the wrench and/or cause personal injury.
DO NOT
drop or throw the wrench.
DO NOT
use the wrench unless you have been instructed in its use
by a qualified person.
DO NOT
leave the wrench in any place exposed to excessive heat,
humidity or direct sunlight.
DO NOT
use organic solvents such as alcohol or thinners to clean
the wrench.
DO NOT
use this wrench in water. (not waterproof). If the wrench
gets wet, dry it immediately.
DO NOT
Over-torque (110% of Max. torque range) could cause
damage or loss of accuracy.
DO NOT
use or store the wrench near a magnet.
DO NOT
expose the wrench to dust or sand as this could cause
serious damage.
DO NOT
apply excessive force to the LCD panel.
After use clean with a soft dry cloth and store in a safe, dry,
childproof location.
Rugged and resilient digital torque wrench suitable for workshop and
factory use. LCD read-out with LED/audible alarm indicates achieved
and target torque levels. Track peak and working torques using simple
push button menu. Selectable read-out in Nm, lb.ft, lb.in or kg.cm.
Reversible Chrome Vanadium ratchet allows torque reading in either
direction. Accurate to ±3% CW and ±4% CCW between 20% and
100% of wrench’s stated capacity. Tested in accordance with EN ISO
6789. Supplied with certificate and storage case.
Thank you for purchasing a Sealey Product. Manufactured to a high standard this tool will, if used according to these instructions and properly
maintained, give years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS,
WARNINGS AND CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS
INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE
WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
INSTRuCTIONS FOR:
1/2” SQ DRIVE DIGITAL
ELECTRONIC TORQUE
WRENCH 40-200Nm
MODEL No:
STW298
1.
SAFETY INSTRUCTIONS
2.
INTRODUCTION & SPECIFICATION
STW298 Issue No: 1 - 02/06/09
2.1 MAIN FEATURES
Digital torque value readout.
+/- 3% accuracy CW and +/- 4% accuracy CCW operation.
Peak-hold and track mode selectable.
Buzzer and LED indicator for the pre-settable target torque.
Engineering units (N-m, ft-lb, in-lb, kg-cm) selectable.
Auto Sleep after about 5 minutes idle.
Compatible with rechargeable batteries.
2.2 NAMES AND FUNCTIONS OF PARTS
10. LED Indicator
11. Torque Value
12. unit (N-m, ft-lb, in-lb, kg-cm)
13. up/Down Button
14. Peak hold/Track mode
15. Power on/Clear Button
16. unit/Setting Button
1. Round Head Ratchet
2. LCD Readout
3. Buzzer
4. Communication Port
5. Button
6. Battery Compartment
7. Battery Cover
8. Ratchet Drive
9. Anti-slip Handle
