![background image](http://html1.mh-extra.com/html/sealey/sjt2/sjt2_instructions_1225341001.webp)
2TONNE/4TONNE TELESCOPIC
BOTTLE JACKS
MODEL NO’S:
SJT2, SJT4
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
WARNING!
ALWAYS USE LOAD RATED STANDS TO SUPPORT LIFTED LOADS
9
Read, study and understand all warnings and operating instructions prior to use. The user shall work in accordance with this manual.
▲
DANGER!
Use the jack for lifting and lowering only.
▲
DANGER!
DO NOT
place any part of the body beneath the lifted load unless the load is fully supported by rated axle stands.
▲
DANGER!
DO NOT
place any part of the body beneath the load during lifting or lowering.
8
DO NOT
exceed the rated capacity of the jack, load or maximum stroke.
8
DO NOT
adjust the overload valve, modify or use the jack for any purpose other than for which it is designed
(lifting and lowering
mechanical devices).
8
DO NOT
leave elevated loads unattended, unless safe from others in a garage or workshop.
8
DO NOT
modify the jack.
9
The operator must watch the jack and the load during all movements.
9
Ensure the jacking area is solid and level. Increase the jacking area with a solid flat plate (steel) if jacking on tarmacadam or grass.
9
Keep others away from the work area.
9
Lift only on areas of the vehicle specified by the vehicle manufacturer. Refer to manufacturer’s instructions on proper lifting.
9
Centre load on saddle prior to lifting.
9
Some vehicles require an adapter to properly engage the frame for lifting.
9
Use only attachments, restraints or adaptors supplied by the manufacturer.
8
DO NOT
move or dolly the the vehicle whilst on the jack.
9
Ensure the jacking area is clutter free and that there is adequate lighting.
WARNING!
Remember, it is very dangerous to go under a vehicle supported by a jack even if additional supports are used.
8
DO NOT
go under a vehicle unless it is supported by adequately rated axle stands. NOTE: Seek advice before jacking caravans or
trailers.
WARNING! The warnings, cautions and instructions in this manual cannot cover all possible conditions and situations
that may occur. It must be understood by the operator that common sense and caution are factors which cannot
be built into this product, but must be applied by the operator.
WARNING! Failure to heed these warnings may result in personal injury and/or property damage.
2. INTRODUCTION
Fitted with overload valve. Dual-stage rams allow for longer travel. Lower retracted and higher extended heights. Base and reservoir machine
welded for increased strength and eliminates leakage. Supplied with 3pc handle.
3. SPECIFICATION
SJT2, SJT4 Issue 1 20/07/22
Original Language Version
© Jack Sealey Limited
Refer to
instructions
Wear safety
footwear
Beware crushing
hands
Wear eye
protection
Wear protective
gloves
Model No.
SJT2
SJT2 Ram Height
SJT4
SJT4 Ram Height
Capacity
2tonne
4tonne
Capacity Stage 1
4000kg
160-240mm
7500kg
170-245mm
Capacity Stage 2
2000kg
240-320mm
4000kg
245-330mm
Screw Extension
60mm
60mm
Hydraulic Lift
160mm
170mm
Maximum Height
370mm
390mm
Minimum Height
150mm
160mm