![background image](http://html.mh-extra.com/html/sealey/sa790/sa790_instruction-manual_1225681001.webp)
Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS,
WARNINGS AND CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH
IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE
THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1.
SAFETY INSTRUCTIONS
p
WARNING!
Ensure Health & Safety, local authority, and general workshop practice regulations are adhered
to when using this equipment.
p
WARNING!
Disconnect from air supply before refilling, servicing or performing maintenance.
3
Maintain the nail gun in good condition (use an authorised service agent).
3
Replace or repair damaged parts.
Use genuine parts only. Non-authorised parts may be dangerous and
will invalidate the warranty.
3
Use in suitable clean and tidy work area, free from unrelated materials and ensure there is adequate lighting.
p
WARNING!
Always wear approved eye and/or face and hand protection when operating the nail gun.
3
Remove ill fitting clothing. Remove ties, loose jewellery, and contain and/or tie back long hair.
3
Wear appropriate protective clothing and keep hands and body clear of working parts.
3
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
3
Keep children and unauthorised persons away from the working area.
3
Check moving parts alignment on a regular basis.
3
Ensure workpiece is secure before operating the nail gun. Never hold a workpiece by hand.
3
When the nail gun is put down during pauses in operation ensure that the trigger catch slide is not
depressed by the weight of the nail gun or by placing the nail gun in a restricted position that could put
pressure on the trigger catch slide.
3
During extended breaks in operation disconnect the nail gun from the air supply.
p
WARNING!
Ensure correct air pressure is maintained and not exceeded. Recommended pressure 60-100psi.
3
Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use and ensure
that all connections are secure.
3
Prolonged exposure to vibration from this nail gun may pose a health risk. It is the owners responsibility to
correctly assess the potential hazard and issue guidelines for safe periods of use and offer suitable protective equipment.
7
DO NOT point the nail discharge outlet at yourself or anyone else. Do not point at animals.
7
DO NOT use any power source except an air compressor.
7
DO NOT operate the nail gun near any flammable substance or on any container that once contained a
flammable substance.
7
DO NOT use the nail gun for a task it is not designed to perform.
7
DO NOT operate nail gun if any parts are damaged or missing as this may cause failure and/or personal injury.
7
DO NOT carry the nail gun by the hose, or yank the hose from the air supply.
7
DO NOT place the nail gun close to your face and do not point at other persons or animals.
7
DO NOT operate nail gun when you are tired, under the influence of alcohol, drugs or intoxicating medication.
7
DO NOT carry the nail gun with your finger on the trigger.
7
DO NOT direct air from the air hose at yourself or others.
3
When not in use, disconnect from air supply and store in a safe, dry, childproof location.
I N S T R U C T I O N M A N U A L F O R :
AIR OPERATED NAIL GUN
M O D E L N O .
SA790
NOTE:
It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component
parts without prior notice.
IMPORTANT:
No liability is accepted for incorrect use of this equipment.
WARRANTY:
Guarantee is 12
months from purchase date, proof of which will be required for any claim.
INFORMATION:
Call us for a copy of our latest catalogue
and promotions on 01284 757525 and leave your full name and address including your postcode.
SA790 - 1 - 170603
ITEM PART NO. DESCRIPTION
1
SA790.01 Bolt M5 x 20
2
SA790.02 Spring washer
3
SA790.03 Cylinder cap
4
SA790.04 Seal washer
5
SA790.05 Compressed spring
6
SA790.06 O-ring 24.8 x 3.5
7
SA790.07 O-ring 31.2 x 2.5
8
SA790.08 Head valve piston
9
SA790.09 O-ring 13.7 x 2.4
10
SA790.10 Piston seal
11
SA790.11
O-ring 4 x 1.8
12
SA790.12 Collar
13
SA790.13 O-ring 30 x 1.8
14
SA790.14 O-ring 42.6 x 2.35
15
SA790.15 Cylinder
16
SA790.16 O-ring 29.7 x 3.55
17
SA790.17 Piston unit
18
SA790.18 D-ring 21 x 3
19
SA790.19 Bumper
20
SA790.20 Gun body
ITEM PART NO. DESCRIPTION
41
SA790.41 Cover plate
42
SA790.42 Pin 1.5 x 10
43
SA790.43 Bolt M4 x 8
44
SA790.44 Driver guide
45
SA790.45 Slice
46
SA790.46 Fixed magazine
47
SA790.47 Movable magazine
48
SA790.48 Fixing screw
49
SA790.49 Support seat
50
SA790.50 Bolt M4 x 12
51
SA790.51 Stopper
52
SA790.52 Stopper pipe
53
SA790.53 Compress spring
54
SA790.54 Fixing bolt
55
SA790.55 Spring lever
(magazine catch)
56
SA790.56 Bolt M4 x 16
57
SA790.57 Stopper
58
SA790.58 Nut M4
59
SA790.59 Hand rubber grip
60
SA790.60 O-ring 36.5 x 3.55
61
SA790.61 End cap
62
SA790.62 Air inlet
ITEM PART NO. DESCRIPTION
21
SA790.21 Grommet
22
SA790.22 Valve sleeve
23
SA790.23 O-ring 11 x 1.2
24
SA790.24 Spring
25
SA790.25 Trigger valve stem
26
SA790.26 O-ring 8 x 1
27
SA790.27 O-ring
28
SA790.28 Valve seat
29
SA790.29 O-ring 11.2 x 1.85
30
SA790.30 Pin
31
SA790.31 Trigger
32
SA790.32 E-ring
33
SA790.33 Safety plate
34
SA790.34 Pin 2.5 x 16
35
SA790.35 Safety guide
36
SA790.36 Spring
37
SA790.37 Safety catch
38
SA790.38 Spacer
39
SA790.39 Release handle
40
SA790.40 Release button
Issue No:
1
Issue Date:
170603
SA790
01284 757500
01284 703534
E-mail:
Sole UK Distributor
Sealey Group,
Bury St. Edmunds, Suffolk.
Web address: www.sealey.co.uk