Sealey SA78X, Instructions

Page: 1 / 2

Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS,
WARNINGS AND CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH
IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE
THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY INSTRUCTIONS
p WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to
when using this equipment.
p WARNING! Disconnect from air supply before refilling with staples, servicing or performing maintenance.
3
Maintain the stapler in good condition (use an authorised service agent).
3
Replace or repair damaged parts. Use genuine parts only. Non-authorised parts may be dangerous and
will invalidate the warranty.
3
Use in suitable clean and tidy working area, free from unrelated materials and ensure there is adequate lighting.
p WARNING! Always wear approved eye or face and hand protection when operating the stapler
3
Remove ill fitting clothing. Remove ties, loose jewellery, and contain and/or tie back long hair.
3
Wear appropriate protective clothing and keep hands and body clear of working parts.
3
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
3
Keep children and unauthorised persons away from the working area.
3
Check moving parts alignment on a regular basis.
3
Ensure workpiece is secure before operating the stapler. Never hold a workpiece by hand.
3
Avoid unintentional operation by always engaging the trigger safety catch when not in use or during pauses
in operation.
p WARNING! Ensure correct air pressure is maintained and not exceeded. Recommended pressure 50-90psi.
3
Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use and ensure
that all connections are secure.
3
Prolonged exposure to vibration from this stapler poses a health risk. It is the Employer’s/Owners and operator’s
responsibility to correctly assess the potential hazard and issue guidelines for safe periods of use and offer
suitable protective equipment.
7
DO NOT point the staple discharge outlet at yourself or anyone else.
7
DO NOT use any power source except an air compressor.
7
DO NOT operate the stapler near any inflammable substance or on any container that once contained an
inflammable substance.
7
DO NOT use the stapler for a task it is not designed to perform.
7
DO NOT operate stapler if any parts are damaged or missing as this may cause failure and/or personal injury.
7
DO NOT carry the stapler by the hose, or yank the hose from the air supply.
7
DO NOT place the stapler close to your face and do not point at other persons or animals.
7
DO NOT operate stapler when you are tired, under the influence of alcohol, drugs or intoxicating medication.
7
DO NOT carry the stapler with your finger on the trigger.
7
DO NOT direct air from the air hose at yourself or others.
3
When not in use engage the trigger safety catch, disconnect from air supply and store in a safe, dry,
childproof location.
SA78X - 2 - 310702
INSTRUCTIONS FOR
AIR OPERATED STAPLER
Model:
SA78X
01284 757500
E-mail: sales@sealey.co.uk
Web: www.sealey.co.uk
01284 703534
Sole UK Distributor, Sealey Group , Bury St. Edmunds, Suffolk.
ITEM PART NO. DESCRIPTION
1 SA78X/01 SCREW 5*22
2 SA78X/02 EXHAUST COVER
3 SA78X/03 COMPRESSION SPRING
4 SA78X/04 SEAL,AIR
5 SA78X/05 CYLINDER CAP
6 SA78X/06 0-RING 11.8*2.4
7 SA78X/07 PISTON SET
8 SA78X/08 WASHER 7.3*4.7*0.8
9 SA78X/09 HEAD VALVE PISTON
10 SA78X/10 PISTON STOPPER
11 SA78X/11 O-RING 26.6*2.4
12 SA78X/12 O-RING 21.3*3
13 SA78X/13 COLLAR
14 SA78X/14 O-RING 33*2
15 SA78X/15 CYLINDER
16 SA78X/16 BUMPER
17 SA78X/17 GASKET
18 SA78X/18 BODY
19 SA78X/19 NOZZLE
20 SA78X/20 SEAL,AIR
21 SA78X/21 TRIGGER VALVE HEAD
22 SA78X/22 TRIGGER VALVE STEM
23 SA78X/23 O-RING 3.8*1.5
24 SA78X/24 TRIGGER VALVE GUIDE
25 SA78X/25 O-RING 9.8*1.9
26 SA78X/26 COMPRESSION SPRING
27 SA78X/27 TRIGGER SPRING
28 SA78X/28 TRIGGER STOPPER
29 SA78X/29 HOLDER SPRING
30 SA78X/30 E-RING 2.5 DIAM
ITEM PART NO. DESCRIPTION
31 SA78X/31 TRIGGER
32 SA78X/32 STEP PIN 5*17.5
33 SA78X/33 O-RING 31.42*2.62
34 SA78X/34 TAIL COVER
35 SA78X/35 AIR PLUG
36 SA78X/36 COMPRESSION SPRING
37 SA78X/37 CLICK LEVER
38 SA78X/38 STEP PIN 5*26
39 SA78X/39 O-RING 17.3*3
40 SA78X/40 PISTON HEAD
41 SA78X/41 DRIVER BLADE PIN
42 SA78X/42 OUTER SPRING PIN 4*10
43 SA78X/43 INNER SPRING PIN 2.5*10
44 SA78X/44 DRIVER BLADE
45 SA78X/45 SCREW 4*16
46 SA78X/46 DRIVER GUIDE
47 SA78X/47 SPACER
48 SA78X/48 SCREW 4*8
49 SA78X/49 STOPPER
50 SA78X/50 UPPER MAG
51 SA78X/51 SCREW 4*8
52 SA78X/52 EXTENSION SPRING
53 SA78X/53 PUSHER
54 SA78X/54 MAGAZINE ASSEMBLY
55 SA78X/55 CYLINDER CAP SET
56 SA78X/56 HEAD VALVE PISTON SET
57 SA78X/57 COLLAR SET
58 SA78X/58 CYLINDER ASSEMBLY
59 SA78X/59 TRIGGER VALVE SET
60 SA78X/60 TRIGGER SET
Issue : 2
Date: 310702