Sealey SA6001, Instructions

Page: 1 / 2

1. SAFETY INSTRUCTIONS
3 Follow all workshop safety rules, regulations, and conditions when using wrench.
p WARNING! Disconnect from air supply before changing accessories or servicing.
3 Maintain the wrench in good condition and replace any damaged or worn parts. Use
genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
p WARNING! Check correct air pressure is maintained and not exceeded. We recommend 90psi.
3 Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each
use and ensure that all connections are secure.
3 Only use impact sockets which are specifically designed for use with an impact wrench.
3 Wear approved safety eye/face shield, ear defenders and hand protection.
p WARNING! Due to the possible presence of asbestos dust from brake linings, when working
around vehicle brake systems we recommend you wear suitable respiratory protection.
3 Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
3 Keep children and non essential persons away from the working area.
7 DO NOT use the wrench for a task it is not designed to perform.
p
p
WARNING! DO NOT use wrench if damaged or thought to be faulty. Contact Service Agent.
7 DO NOT use wrench unless you have been instructed in its use by a qualified person.
7 DO NOT carry the wrench by the air hose, or yank the hose from the air supply.
7 DO NOT operate wrench if you are tired or under the influence of alcohol, drugs or intoxicating medication.
7 DO NOT carry wrench with your hand on the power trigger in order to avoid unintentional starting.
7 DO NOT direct air from the air hose at yourself or others.
3 When not in use disconnect from air supply and store in a safe, dry, childproof location.
2. INTRODUCTION & SPECIFICATION
Composite casing with soft grip makes the tool lighter, easier to handle and helps reduce vibration
and chill. Handle exhaust reduces noise level. New pin clutch design gives the wrench a high
torque output making it suitable for jobs that would normally require a 3/4” impact wrench. Dial
type power and direction control on rear of wrench. Suitable for heavy tyre shop use.
SA6001 - 1 - 120705
Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these
instructions and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS,
WARNINGS AND CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH
IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE
THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
INSTRUCTIONS FOR:
PIN CLUTCH AIR IMPACT
WRENCH 1/2” DRIVE
MODEL NO:
SA6001
Working/Maximum Torque: . . . . . .700/800lb.ft
Ultimate Torque: . . . . . . . . . . . . . . . . . .950lb.ft
Air Consumption: . . . . . . . . . . . . . . . . . .13cfm
Operating Pressure: . . . . . . . . . . . . . . . .90psi
Air Inlet Size: . . . . . . . . . . . . . . . . . . .1/4“BSP
Weight: . . . . . . . . . . . . . . . . . . . . . . . . . .2.1kg
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component
parts without prior notice. IMPORTANT: No liability is accepted for incorrect use of this equipment. WARRANTY: Guarantee is 12
months from purchase date, proof of which will be required for any claim. INFORMATION: For a copy of our latest catalogue and
promotions call us on 01284 757525 and leave your full name and address, including postcode.
01284 757500
E-mail: sales@sealey.co.uk
Web: www.sealey.co.uk
01284 703534
Sole UK Distributor, Sealey Group , Bury St. Edmunds, Suffolk.
PARTS LIST FOR:
PIN CLUTCH AIR IMPACT
WRENCH 1/2” DRIVE
MODEL NO:
SA6001
ITEM PART NO. DESCRIPTION
01. SA6001.01 OIL SEAL
02. SA6001.02 HAMMER CASE
03. SA6001.03 BUSHING
04. SA6001.04 FRONT GASKET
05. SA6001.05 MOTOR HOUSING
06. SA6001.06 WASHER
07. SA6001.07 O-RING
08. SA6001.08 ANVIL COLLAR
09. SA6001.09 ANVIL
10. SA6001.10 SPRING
11. SA6001.11 HAMMER PIN
12. SA6001.12 BALL
13. SA6001.13 HAMMER CAGE
14. SA6001.14 TRIGGER
15. SA6001.15 O-RING
16. SA6001.16 SPRING PIN
17. SA6001.17 RUBBER
18. SA6001.18 HAMMER CAM
19. SA6001.19 SPINDLE GUIDE
20. SA6001.20 RETAINER
21. SA6001.21 VALVE STEM
22. SA6001.22 SPRING
ITEM PART NO. DESCRIPTION
23. SA6001.23 EXHAUST DEFLECTOR
24. SA6001.24 O-RING
25. SA6001.25 HOSE ADAPTOR
26. SA6001.26 BALL BEARING
27. SA6001.27 O-RING
28. SA6001.28 OIL SEAL
29. SA6001.29 CYLINDER
30. SA6001.30 SPRING PIN
31. SA6001.31 ROTOR
32. SA6001.32 ROTOR BLADE
33. SA6001.33 REAR PLATE
34. SA6001.34 BALL BEARING
35. SA6001.35 PIN
36. SA6001.36 SPRING
37. SA6001.37 O-RING
38. SA6001.38 REAR GASKET
39. SA6001.39 REAR COVER
40. SA6001.40 O-RING
41. SA6001.41 SCREW & WASHER
42. SA6001.42 REVERSE LEVER
43. SA6001.43 O-RING
44. SA6001.44 WASHER
Issue: . . . . . . . . . . . .1
Issue Date: . . .120705