Ø6mm 4500rpm mini 90° Angle Air Drill
Key ChuCK
Model no:
SA1008
Thank you for purchasing a Sealey product. manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAfeTy
WArning!
ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this
equipment.
WArning!
disconnect from air supply before changing drill bits, servicing, or performing any maintenance.
9
Maintain the drill in good condition (use an authorised service agent).
9
Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
9
Use in a suitable work area. Keep area free from unrelated materials and ensure that there is adequate lighting.
9
Before each use check condition of drill bit. Sharpen if necessary. If worn or damaged, replace immediately.
9
ensure the speed rating (rpm) of the drill bit is the same as, or greater than, the speed rating of the drill.
9
Ensure there are no flammable or combustible materials near the work area.
9
Evaluate your working area before using the drill. Ceilings, floors and enclosures may contain hidden electrical wiring, water pipes or
gas pipes.
WArning!
Always wear approved eye (or face) and hand protection when operating the drill.
9
Use face, dust, or respiratory protection in accordance with CoSHH regulations.
9
depending on the task, the drilling noise level may exceed 84dB in which case wear safety ear defenders.
9
Remove ill fitting clothing remove ties, watches, rings, other loose jewellery and contain and/or tie back long hair.
9
Wear appropriate protective clothing and keep hands and body clear of working parts.
9
Maintain correct balance and footing.
Do noT
over reach, ensure the floor is not slippery, wear non-slip shoes.
9
Keep children and unauthorised persons away from the working area.
9
Check moving parts alignment on a regular basis.
9
ensure workpiece is secure before operating the drill.
Do noT
hold a workpiece by hand.
9
Check the workpiece to ensure there are no protruding screws, bolts, nuts etc.
9
Avoid unintentional starting.
9
Remove chuck key before starting the drill.
WArning!
Ensure correct air pressure is maintained and not exceeded. Recommended pressure 70-90psi
9
Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use and ensure that all connections are
secure.
9
Prolonged exposure to vibration from this drill poses a health risk. It is the owner’s responsibility to correctly assess the potential
hazard and issue guidelines for safe periods of use and offer suitable protective equipment.
8
Do noT
use the drill for a task it is not designed to perform.
8
Do noT
operate drill if any parts are damaged or missing as this may cause failure and/or personal injury.
WArning!
Do noT
drill any materials containing asbestos.
8
Do noT
carry the drill by the hose, or yank the hose from the air supply.
8
Do noT
force, or apply heavy pressure to the drill; let the tool do the work.
8
Do noT
place air line attachments close to your face and
Do noT
point at other people or animals.
8
Do noT
operate drill when you are tired, under the influence of alcohol, drugs or intoxicating medication.
8
Do noT
use drill where there are flammable liquids, solids or gases such as paint solvents and including waste wiping or cleaning
rags etc.
8
Do noT
carry the drill with your hand on the trigger.
9
When not in use disconnect from air supply and store in a safe, dry, childproof location.
2. inTroDuCTion
T
extured finish to ensure a good grip. Mini design for working in confined areas, ideal for working around engines where space is limited.
Powerful mini drill 4500rpm, Ø6mm key chuck 1 - 6mm drill bits. Safety trigger prevents inadvertent operation. Suitable for professional
workshop use. Supplied with chuck key.
S
A1008 Issue 2 (3) 19/12/19
Original Language Version
© Jack Sealey limited
Refer to
instructions
Wear eye
protection
Wear protective
gloves
Wear ear
protection
Wear a mask
