background image

90° Ø6mm Collet mini Air Die GrinDer

Model no: 

SA1005 

thank you for purchasing a Sealey product. manufactured to a high standard, this product will, if used according to these 

instructions, and properly maintained, give you years of trouble free performance.

IMPORTANT:

 PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE 

THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR 
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

1.  SAfety

 

‰

  

WArninG!

 Wear approved eye and ear protection. Wear appropriate Personal Protective equipment. A full range of PPe is  

 

  available from your Sealey stockist. Be aware of CoSHH when it applies.

 

‰

  

WArninG!

 ensure Health & Safety, local authority and general workshop practice regulations are adhered to when using this    

 equipment.

 

‰

  

WArninG!

 disconnect from the air supply before changing the grinding wheel bit, servicing or performing maintenance.

 

‰

  

WArninG!

 ensure correct air pressure is maintained and not exceeded. Recommended air line pressure is 90psi.

 

9

   Maintain the tool in good condition (use an authorised service agent).

 

9

   Replace damaged parts/bits. Use genuine parts/bits only. Unauthorised parts/bits may be dangerous and will invalidate the warranty.

 

9

   Use in a suitable clean and tidy work area, free from unrelated materials. ensure that there is adequate lighting and ventilation.

 

9

   Remove ill fitting clothing. Remove ties, loose jewellery and contain and/or tie back long hair.

 

9

   Keep children and unauthorised persons away from the work area.

 

9

   Before each use, check the grinding bit is secure and sound. If worn or damaged, replace immediately.

 

9

   ensure the workpiece is secure. never hold a workpiece in the hand; use a vice or clamps.

 

9

   Keep the air hose away from heat, oil and sharp edges. Check air hose for wear before each use and ensure that all connections are  

 secure.

 

9

   Prolonged exposure to vibration from this tool poses a health risk. It is the employer’s/owner’s responsibility to correctly assess the  

  hazard and issue guidelines for safe periods of use and offer suitable protective equipment. Safety gloves are recommended.

 

9

   When not in use, disconnect from the air supply and store complete in the supplied case.

 

9

   Wear breathing apparatus when fumes or dust pose a hazard. Be aware of and adhere to CoSHH regulations.

 

8

  

Do not

 grind materials containing asbestos.

 

8

  

Do not

 use any power source except an air compressor.

 

8

  

Do not

 operate the tool near any inflammable substance or on any container that has held an inflammable substance.

 

8

  

Do not

 use the tool for a task it is not designed to perform.

 

8

  

Do not

 operate the tool if unwell, tired or intoxicated.

 

8

  

Do not

 carry the tool by the hose, or yank the hose from the air supply.

 

‰

  

WArninG!

 The warnings, cautions and instructions in this manual cannot cover all possible conditions and situations that may    

  occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but  

  must be applied by the operator.

2.  introDuCtion

T

extured finish to ensure a good grip. Mini design for working in confined areas, ideal for working around engines where space is limited. 

Safety trigger prevents inadvertent operation. Ideal for re-shaping, deburring and smoothing off rough edges on castings. Suitable for the 

professional workshop. Supplied with fitting spanner.

3.  SpeCifiCAtion

model no: ................................................................. SA1005

Air Consumption:.......................................................... 12cfm

Air Inlet Size: .............................................................1/4”BSP

Collet diameter: ............................................................. 6mm

C

onfiguration:

 ..........................................................90° - Mini

Free Speed: ........................................................... 16500rpm

length: ....................................................................... 125mm

noise Power/Pressure: ........................................ 97dB/86dB

operating Pressure: ...................................................... 80psi

Vibration/Uncertainty: ................................... 1.079/0.602m/s²

SA1005 Issue 2 (3) 18/12/19

Original Language Version

© Jack Sealey limited

Refer to 

instructions

Wear eye 

protection

 Wear ear 

protection

 Wear a mask  Wear protective 

gloves

Reviews: