15TONNE PREMIER HYDRAULIC PRESS -
BENCH TYPE
MODEL NO:
PPB15S
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
9
Familiarise yourself with the applications, limitations and hazards of the press.
9
Maintain the press in good condition (use an authorised service agent).
9
Replace or repair damaged parts. Use recommended parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
9
Keep the press clean for best and safest performance.
9
Locate the press in a suitable work area, on a surface that is stable, level, dry, not slippery, and capable of sustaining the load.
9
Keep area clean and tidy and free from unrelated materials, and ensure there is adequate lighting.
WARNING!
Always wear approved eye or face protection when operating the press.
9
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery, and contain long hair.
9
Keep hands and body clear of the work table when operating the press.
9
Maintain correct balance and footing.
DO NOT
over reach. Ensure the floor is not slippery and wear non-slip shoes.
9
Keep children and unauthorised persons away from the working area.
8
DO NOT
use the press for a task it is not designed to perform.
8
DO NOT
adjust or tamper with the safety valve, or make any modifications to the press.
8
DO NOT
exceed the rated capacity of the press. Avoid applying excessive force, use the pressure gauge to determine the applied load.
8
DO NOT
apply off-centre loads. Ensure that workpiece is centrally loaded and correctly secured before operating the press.
8
DO NOT
allow the workpiece or the arbor plates to fall from the press work bench.
8
DO NOT
get the press wet or use in damp or wet locations or areas where there is condensation.
8
DO NOT
operate the press when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
DO NOT
climb upon the press.
8
DO NOT
use if bent, broken, cracked, leaking or otherwise damaged, or if press has been subjected to a shock load.
8
DO NOT
operate the press if any parts are missing as this may cause failure and/or possible personal injury.
8
DO NOT
use the press to compress a spring or any other item that could disengage and cause a potential hazard.
8
DO NOT
stand directly in front of loaded press and never leave loaded press unattended.
8
DO NOT
allow untrained persons to operate the press.
▲
DANGER!
This model is purpose designed to withstand greater loads than the hydraulic unit can develop. For safety reasons, always
ensure the workpiece and press tools are secured on the table and will not flex or suddenly give way, causing danger to operator or
the workpiece.
WARNING! DO NOT use brake fluid, or any fluid other than a good quality jack oil, such as SEALEY HYDRAULIC JACK OIL, as
this may cause serious damage to the press and will invalidate the warranty.
9
When not in use, release pressure from the pump and clean the press. Stand or store the arbors in a safe, childproof location.
2. INTRODUCTION
Heavy-duty steel frame construction with handle operated hydraulic pump unit. Screw adjustable ram and adjustable work area with removable
tray. Frame head fitted with ram pressure gauge. Storage for press pins included in frame. Supplied with press pins, flat pressing plate/V-blocks.
Suitable for workshop use or by the serious motoring enthusiast.
3. SPECIFICATION
Model No:
................................................................
PPB15S
Capacity: ................................................................... 15tonne
Maximum Height - Ram to Table: ............................... 385mm
Minimum Height - Ram to Table: .................................. 45mm
Overall Height: ........................................................... 855mm
Ram Diameter: .......................................................... Ø78mm
Ram Stroke: ................................................................. 95mm
Screw Extension: ......................................................... 75mm
Table Aperture: ........................................................... 147mm
Total Ram Travel: ....................................................... 170mm
Type: ................................................................... Bench Type
Working Table Depth: ................................................. 163mm
Working Table Width: ................................................. 565mm
Refer to
instruction
manual
Wear a face
shield
Wear protective
gloves
Wear safety
footwear
Wear protective
clothing
Beware
crushing of
hands
No reaching in
Piston rod
should face
workpiece
Place V block
correctly
PPB15S Issue 1 18/02/22
Original Language Version
© Jack Sealey Limited
