PREMIER BOTTLE JACK
20TONNE, 30TONNE & 50TONNE
MODEL NO:
PBJ20, PBJ30 & PBJ50
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
WARNING!
ALWAYS USE LOAD RATED STANDS TO SUPPORT LIFTED LOADS
▲
DANGER!
Use the jack for lifting and lowering only.
▲
DANGER!
DO NOT
place any part of the body beneath the lifted load unless the load is fully supported by rated stands.
▲
DANGER!
DO NOT
place any part of the body beneath the load during lifting or lowering.
8
DO NOT
exceed the rated capacity of the jack, load or maximum stroke.
8
DO NOT
adjust the overload valve, modify or use the jack for any purpose other than for which it is designed
(lifting and lowering
mechanical devices).
8
DO NOT
leave elevated loads unattended, unless safe from others in a garage or workshop.
8
DO NOT
modify the jack.
9
Ensure the jacking area is solid and level. Increase the jacking area with a solid flat plate (steel) if jacking on tarmacadum or grass.
9
Keep others away from the work area.
9
Ensure the jacking area is clutter free and that there is adequate lighting.
WARNING! The warnings, cautions and instructions in this manual cannot cover all possible conditions and situations that
may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into
this product, but must be applied by the operator.
2. INTRODUCTION
Fitted with safety overload valve and manufactured in the EU. All steel, one-piece base, reservoir and pump cylinder design gives added
strength. Fully serviceable ram piston with extension screw. All models supplied with 90° rotating pump and telescopic pump handle. Model
No’s PBJ20, PBJ30 and PBJ50 have moulded carry handles incorporating storage for the pump handle. Service kits readily available.
3. SPECIFICATION
Model No: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PBJ20 . . . . . . . . . . . PBJ30 . . . . . . . . . . PBJ50
Capacity:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20tonne . . . . . . . . . . 30tonne . . . . . . . . . 50tonne
Hydraulic Lift: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .150mm . . . . . . . . . . .150mm . . . . . . . . . .140mm
Maximum Height: (Leadscrew extended). . . . . . . . . . . .459mm . . . . . . . . . . .467mm . . . . . . . . . .400mm
Minimum Height: (Leadscrew retracted) . . . . . . . . . . . .234mm . . . . . . . . . . .242mm . . . . . . . . . .260mm
Screw Extension: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75mm . . . . . . . . . . . .75mm . . . . . . . . . . . . . . *0 *
Note: no leadscrew on Model PBJ50
Nett Weight: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.89kg . . . . . . . . . . 15.37kg . . . . . . . . . 26.77kg
PBJ20, PBJ30, PBJ50 | Issue 3 (H,F) 17/01/19
Original Language Version
© Jack Sealey Limited
Refer to
instructions
Wear safety
footwear
Beware crushing
hands
Jack Saddle
axis in line
(no offset load)
Use wheel
chocks
Use axle stands
PBJ20
PBJ30
PBJ50
