![background image](http://html.mh-extra.com/html/sealey/pb1000/pb1000_instructions_1224307001.webp)
3
Ensure that the pulley block is in sound condition and good working order. Take action for immediate repair or replacement of damaged parts.
3
Use recommended parts only. The use of unauthorised parts may be dangerous and will invalidate the warrentry.
3
Ensure the support for the pulley block is capable of withstanding a load of at least 1½ times the safe working load of the block.
3
Keep the pulley block clean for the best and safest performance.
3
Locate the pulley block in a suitable, well-lit area.
3
Keep work area clean and tidy and free from unrelated materials.
3
Ensure all non-essential persons keep a safe distance whilst the pulley block is in use.
3
Ensure load slings are fully engaged in the load hook and that the hook safety bar is in the closed
position.
3
Raise and lower a load on the pulley in a smooth, controlled manner.
DO NOT
shock load the pulley
block.
by allowing the attached load to fall freely, even for very short distances.
p
p
DANGER:
Use the pulley block for lifting only,
NOT
for suspending the lifted load.
3
Use a qualified person to lubricate and maintain the pulley block.
7
DO NOT
operate the pulley block if it is damaged.
7
DO NOT
allow untrained persons to operate the pulley block.
7
DO NOT
exceed the rated capacity (working load) of the pulley block. (See Section 5).
7
DO NOT
raise or lower the load with jerky or abrupt movements of the rope.
7
DO NOT
attempt to lift a load if the load rope is kinked or knotted.
7
DO NOT
try to raise a load with two, or more, pulley blocks - use a single block of adequate
capacity.
7
DO NOT
use the pulley block to drag the load across the floor. Always position the load directly
below the block.
7
DO NOT
wrap the load rope around the load - always use separate, suitable, ropes or slings of the
correct capacity.
7
DO NOT
allow anyone to stand, or pass beneath, the raised load.
7
DO NOT
use the pulley block for purposes other than that for which it is intended.
3
Store the pulley block in a dry, childproof area when not in use.
IMPORTANT: Use only with wire rope of the specified diameter.
DO NOT
attempt to free a jammed rope or pulley while a load is attached. Use alternative means to support the load and unhook the rope from the load
before rectifying the jam.
BEWARE!
Broken rope strands or unfinished rope ends present risk of personal injury, i.e. a puncture wound.
INSTRUCTIONS FOR:
PULLEY BLOCK
Models
:
PB1000, PB2000, PB3000
IMPORTANT:
READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS, AND CAUTIONS. USE
THE PULLEY BLOCK CORRECTLY, AND WITH CARE, FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY.
1. SAFETY INSTRUCTIONS
2. SPECIFICATION
3. OPERATION
Sole UK Distributor,
Sealey Group,
Bury St. Edmunds, Suffolk.
01284 757500
01284 703534
Thank you for purchasing a Sealey pulley block. This product is manufactured to a high standard of dependability and, if correctly cared for, will give
you years of trouble free performance.
Fig 1: Pulley Block
IMPORTANT: Before using the pulley block ensure that you have read, understood and applied the safety instructions in Section 1.
NOTE:
This pulley block will normally be used in conjunction with a mechanical pulling device and should never be operated by hand. Wear safety gloves and keep
hands away from moving pulley wheels.
3.1.
Rotate the hook to release the hinge plate and place the rope on the pulley groove. Close the hinge plate and rotate the hook through 90° to lock it.
DO NOT
attempt to use the pulley block with the hinge plate open.
3.2.
If using the pulley block for simple lifting (Section 5.A) ensure that it is suspended from a structure capable of supporting at least 1½ times the safe working load
of the block.
3.3.
Ensure that the block hook is fully engaged with the safety bar closed. Confirm that the total load does not exceed the working load of the block. See Section 5.
3.4.
Ensure that the lifting rope is securely and safely attached to the load and that the load is directly below the block.
3.5.
Take up the tension in the rope until the load rope is taut and not pulling at an angle.
3.6.
Start to raise the load and ensure that it is level, with no possibility of the load tilting and/or slipping from its restraints. If necessary, lower the load and readjust
the attachment point to obtain a safe, level lift.
NOTE: DO NOT
suddenly release the pulley rope, as the pulley has no braking system attached to it
.
3.7.
Continue to raise the load to the required height in a slow, controlled manner.
DO NOT
raise the load so far that the hook comes into contact with the block.
3.8.
Lower the load slowly and smoothly, avoiding jerky or abrupt movements.
3.9.
If, at any time, the rope will not move in either direction do not attempt to force it but, after arranging safe support for any suspended load, have the block
inspected by an Authorised Service Agent.
PB1000, PB2000, PB3000 - 1 - 081205
www.sealey.co.uk
*
Ambient operating temperature range: -10°C to +50°C.
Refer to Figure 1