instructions for
hydraulic scissor jack 700kg
model no:
hsj07
Thank you for purchasing a sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. safeTy
9
ensure the jack is in sound condition and good working order. take action for immediate repair or replacement of damaged parts.
use genuine parts only. the use of improper parts may be dangerous and will invalidate the warranty.
9
locate the jack in a suitable, well lit working area. Keep working area clean and tidy and free from unrelated materials.
9
use jack on level/solid ground, preferably concrete. Avoid tarmacadam as jack may sink in.
9
Place wedges under wheels of vehicle, but ensure the jack wheels are free to move and that there are no obstructions.
9
ensure the vehicle handbrake is engaged, engine is switched off and transmission is in gear (or “PArK” if automatic).
9
ensure minimum distance of 0.5m between vehicle and static objects such as doors, walls, etc., to allow for vehicle tilting.
9
ensure there are no passengers in the vehicle and that all non-essential persons keep a safe distance whilst the jack is in use.
Place jack under lifting points recommended by vehicle manufacturer (see vehicle hand book). ensure lifting point is stable and centred
on saddle.
▲
daNger:
use the jack for lifting only, not for supporting the lifted load.
9
use suitable capacity axle stands under the vehicle before proceeding with any task.
9
ensure there are no persons or obstructions beneath the vehicle before lowering.
8
do NoT
operate the jack if damaged.
8
do NoT
work under the vehicle until axle stands have been correctly positioned.
8
do NoT
exceed the rated capacity of the jack. When lifting a load of maximum capacity or close to it, it is recommended that the effort
be reduced by the use of assistance during this operation.
8
do NoT
adjust the safety overload valve.
8
do NoT
jack vehicle if there is a risk of spillage of fuel, battery acid, or other dangerous substances.
8
do NoT
allow the vehicle to move while supported by the jack, or use the jack to move the vehicle.
8
do NoT
top up hydraulic system with brake fluid. use hydraulic jack oil only and use a qualified person to maintain jack hydraulic
system.
8
do NoT
allow untrained persons to operate the jack.
8
do NoT
use jack for purposes other than which it is designed.
8
do NoT
allow persons to ride on the jack.
When not in use store jack, fully lowered, in a safe, dry, childproof area.
2. iNTroducTioN
s
cissor jack fitted with a hydraulic unit to provide the space saving properties of a conventional scissor jack with the convenience of a trolley
jack. the hydraulic unit greatly reduces the time and effort taken to raise a vehicle compared to a standard scissor jack. suitable for the hobby
user or as an emergency mobile jack. includes one-piece pumping handle. supplied in tough carry/storage case to keep dirty jack away from
contents of car boot.
3. specificaTioN
model no ..................................................................... HsJ07
capacity ....................................................................... 700kg
minimum Height ......................................................... 139mm
maximum Height ........................................................ 380mm
closed length ............................................................ 382mm
4. operaTioN
4.1.
Before use.
4.1.1. Before using jack for the first time, purge the hydraulic unit in order to eliminate any air in the system. Position handle extension over
release valve turn handle anti clockwise to open release valve. Attach handle extension to handle.
4.1.2.
Pump for 30 to 40 seconds. When complete, close the release valve by turning the clockwise.
4.1.3.
Place a few drops of hydraulic jack oil on pump piston and pump handle several times to distribute oil. thoroughly lubricate moving
parts.
HsJ07 | issue 1 04/11/16
Original Language Version
© Jack sealey limited
refer to
instructions
Wear safety
footwear
