background image

 

 

WARNING!

 Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when building this shed.

 

 

Keep the work area clean, uncluttered and ensure there is adequate lighting.

 

 

Keep children and unauthorised persons away from the working area.

 

DO NOT

 use the shed for any purpose other than that for which it is designed.

 

 

Use appropriate safety clothing including eye protection.

  

The assembly of this product will require assistance.

 

DO NOT 

attempt assembly in windy conditions.

INSTRUCTIONS FOR: 

GALVANIZED STEEL SHED GREEN

1.5 X 1.5 X 1.9M

MODEL NO:

 GSS1515G

IMPORTANT:

 

PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.  USE 

THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR 

PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these 

instructions, and properly maintained, give you years of trouble free performance.

 1.  SAFETY

 2.  INTRODUCTION

 3.  SPECIFICATION

Galvanized, steel panels easily assembled to form a rigid and secure shed,  has skillion (sloping) roof and single door. Door is secured by cross 

bolt and eyelet which will accept a padlock (not supplied) for additional security. Supplied with bolt-down fixing kit. 

Model No:  . . . . . . . . . . . . . . . . . . GSS1515G

Overall Size: . . . . . . . .

1500 x 1500 x 1900mm

Roof Type:  . . . . . . . . . . . . . . . . . . . . . . Skillion

Original Language Version

GSS1515G    Issue: 1 - 26/09/14

 © Jack Sealey Limited

Summary of Contents for GSS1515G


















Reviews: