background image

INSTRUCTIONS FOR

150MM DUAL ACTION

RANDOM ORBITAL SANDER

Thank you for purchasing a Sealey Product. Manufactured to a high

standard this product will, if used according to these instructions and

properly maintained, give you years of trouble free performance.

EDA150 - 0050 - 050199

IMPORTANT:

PLEASE READ INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS.

USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE

DAMAGE OR PERSONAL INJURY, AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.

Sole UK Distributor, Sealey Group

Bury St. Edmunds, Suffolk.

01284 757500

E-mail:

[email protected]

01284 703534

NOTE:

It is our policy to continually improve products and as such we reserve the right to alter data,

specifications and component parts without prior notice.

IMPORTANT: 

No liability is accepted for incorrect use of this equipment.

WARRANTY: 

Guarantee is 12

months from purchase date, proof of which will be required for any claim. 

INFORMATION: 

Call us for a

copy of our latest catalogue on 01284 757525 and leave your full name, address including your postcode.

We, the sole importer into the UK, declare that the product listed here 

is

in conformity

with the following EEC standards and directives. The construction file for th

is 

product

is

held  by the Manufacturer and may be inspected on request by contacting Jack

Sealey Ltd

For Jack Sealey Ltd. Sole importer into the UK of Sealey 

Power Tools.

150MM DUAL ACTION RANDOM ORBITAL

SANDER Model:  EDA150

73/23/EEC

Low Voltage Directive (S.I. 1994/3260)

89/336/EEC

EMC Directive (S.I.  1992/2372 & Amendments)

Signed by John Sealey

1st February 1999

Model:

EDA150

Declaration of Conformity 

1.

SAFETY INSTRUCTIONS

1.1.

ELECTRICAL SAFETY.  

p

WARNING!

It is the user’s responsibility to read, understand and comply as

follows. 

You must

check all electrical equipment and appliances to ensure they are safe before using. 

You 

must

inspect power supply leads, plugs and all electrical connections for wear and damage. 

You must

ensure the risk of electric shock is minimised by the installation of appropriate safety devices. An RCCB 

(Residual Current Circuit Breaker) should be incorporated in the main distribution board. We also recommend 

that an RCD (Residual Current Device) is used with all electrical products. It is particularly important to use 

an RCD  together with portable products that are plugged into an electrical supply not protected by an RCCB. 

If in doubt consult a professional electrician. You may obtain a Residual Current Device by contacting your 

Sealey dealer. 

You must

also read and understand the following instructions concerning electrical safety.

1.1.1. The Electricity At Work Act 1989 requires all portable electrical appliances, if used on a business premises,

to be tested by a qualified Electrician at least once a year by using a Portable Appliance Tester (PAT).

1.1.2. The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of the

appliance, and the safety of the appliance operator. If in doubt about electrical safety, contact a qualified electrician.

1.1.3. Ensure the insulation on all cables and the product itself is safe before connecting to the mains power

supply. See 1.1.1. & 1.1.2. above and use a Portable Appliance Tester (PAT).

1.1.4. Ensure that cables are always protected against short circuit and overload.

1.1.5. Regularly inspect power supply, leads, plugs and all electrical connections for wear and damage, 

especially power connections, to ensure that none are loose. 

1.1.6. Important: Ensure the voltage marked on the product is the same as the electrical power supply to be

used, and check that plugs are fitted with the correct capacity fuse. A 13Amp plug may require a fuse 

smaller than 13Amps for certain products (subject to 1.1.10. below) see fuse rating below. 

1.1.7. DO NOT pull or carry the powered appliance by its power supply lead. Products such as welders must not

be pulled or carried by their output cables.

1.1.8. DO NOT pull power plugs from sockets by the power cable.

1.1.9. DO NOT use worn or damaged leads, plugs or connections.

Immediately replace or have repaired by a qualified Electrician.

A U.K. 3 pin plug with ASTA/BS approval is fitted. In case 

of damage, cut off and fit a new plug according to the following

instructions (discard old plug safely). (UK only - see diagram at right).  

Ensure the unit is correctly earthed via a three-pin plug. 

a) Connect the green/yellow earth wire to the earth terminal ‘E’.

b) Connect the brown live wire to live terminal ‘L’.

c) Connect the blue neutral wire to the neutral terminal ‘N’.

After wiring, check there are no bare wires, that all wires 

have been correctly connected and that the wire restraint is tight.

Double insulated products are often fitted with live (BROWN) 

and neutral (BLUE) wires only. Double insulated products are always marked 

with this symbol       . Check you model carefully to see which type of product

your have. To re-wire, a double insulated item, connect the brown and blue 

wires as indicated above. DO NOT connect brown or blue to the earth terminal.

1.1.10. Cable extension reels. When a cable extension reel is used it should be fully

unwound before connection. A cable reel with an RCD fitted is recommended 

since any product which is plugged into the cable reel will be protected. 

The section of the cable on the cable reel is important. We recommend that at least 1.5mm

2

section cable 

but to be absolutely sure that the capacity of the cable reel is suitable for this product and for others that 

may be used in the other output sockets, we recommend the use of 2.5mm

2

section cable.

Yellow & Green 

Earth wire 

FUSE RATING

THIS PRODUCT MUST BE 

FITTED WITH A: 

Amp FUSE

Brown

Live 

wire

Blue

Neutral 

wire

wire 

restraint

Reviews: