Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and
properly maintained, give you years of trouble free performance.
IMPORTANT
:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS, AND
CAUTIONS. USE THIS PRODUCT CORRECTLY, AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO
MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY.
1. SAFETY INSTRUCTIONS
inSTrucTionS for:
CORDLESS GREASE
GUN 18V
MoDEL no:
CPG18V
1.1.
ELECTRICAL SAFETY
WARNING!
it is the responsibility of the owner and the operator
to read, understand and comply with the following:
You must check all electrical products, before use, to ensure that
they are safe. You must inspect power cables, plugs, sockets and
any other connectors for wear or damage. You must ensure that the
risk of electric shock is minimised by the installation of appropriate
safety devices. A residual current circuit Breaker (rccB) should be
incorporated in the main distribution board. We also recommend that
a residual current Device (rcD) is used. it is particularly important
to use an rcD with portable products that are plugged into a supply
which is not protected by an rccB. if in any doubt consult a quali-
fied electrician. You may obtain a residual current Device by
contacting your Sealey dealer. You must also read and understand
the following instructions concerning electrical safety.
1.1.1. The
Electricity at Work Act 198
9 requires that all portable
electrical appliances, if used on business premises, are
tested by a qualified electrician, using a Portable Appliance
Tester (PAT), at least once a year.
1.1.2. The
Health & Safety at Work Act 1974
makes owners of
electrical appliances responsible for the safe condition of
those appliances and the safety of the appliance operators. if
in any doubt about electrical safety, contact a qualified
electrician.
1.1.3. Ensure that the insulation on all cables and on the appliance
is safe before connecting it to the power supply. See 1.1.1.
and 1.1.2. and use a Portable Appliance Tester.
1.1.4. Ensure that cables are always protected against short circuit
and overload.
1.1.5. regularly inspect power supply cables and plugs for wear or
damage and check all connections to ensure that none is loose.
1.1.6.
Important:
Ensure that the voltage marked on the appliance
matches the power supply to be used and that the plug is
fitted with the correct fuse - see fuse rating above/right.
1.1.7.
DO NOT
pull or carry the appliance by the power cable.
1.1.8.
DO NOT
pull the plug from the socket by the cable.
1.1.9.
DO NOT
use worn or damaged cables, plugs or connectors.
immediately have any faulty item repaired or replaced by a
qualified electrician. When a BS 1363/A uK 3 pin plug is
damaged, cut the cable just above the plug and
dispose of
the plug safely
. fit a new plug according to the following
instructions (uK only). See above/right.
a) Connect the GREEN/YELLOW earth wire to the earth
terminal ‘E’.
b) Connect the BROWN live wire to the live terminal ‘L’.
c) Connect the BLUE neutral wire to the neutral terminal ‘N’.
d) After wiring, check that there are no bare wires, that
all wires have been correctly connected, that the
cable outer insulation extends beyond the cable
restraint and that the restraint is tight.
Double insulated products, which are always marked with
this symbol , are fitted with live (brown) and neutral (blue)
wires only. To rewire, connect the wires as indicated above/
right.
DO NOT
connect either wire to the earth terminal.
1.1.10. Products which require more than 13 amps are supplied
without a plug. in this case you must contact a qualified
electrician to ensure that a suitably rated supply is available.
We recommend that you discuss the installation of an
industrial round pin plug and socket with your electrician.
1.1.11. if an extension reel is used it should be fully unwound before
connection. A reel with an rcD fitted is preferred since any
appliance plugged into it will be protected. The cable core
section is important
and should be at
least 1.5mm², but to
be absolutely sure
that the capacity of
the reel is suitable
for this product and
for others which may
be used in the other
output sockets, we
recommend the use
of 2.5mm² section
cable.
1.2 GENERAL SAFETY
WARNING!
Disengage the grease gun from the battery before changing
accessories, servicing or performing and maintenance.
Maintain gun in good condition (use an authorised service
agent).
replace or repair damaged parts.
Use recommended parts only.
Unauthorised parts may be dangerous and will invalidate the
warranty.
Wear appropriate protective clothing. When handling lubricants
refer to manufacturer’s instructions and conform to local
regulations.
use the gun in a suitable working area. Keep area clean and
tidy and free from unrelated materials and ensure there is
adequate lighting.
Maintain correct balance and footing whilst performing the task.
Ensure floor is not slippery and wear non-slip shoes.
Keep children and unauthorised persons away from the work area.
Dispose of waste grease in accordance with local authority
regulations.
When not in use ensure the battery is removed.
Do noT allow unauthorised persons to operate the gun.
WARNING! DO
NOT tamper with
or open pump unit.
Doing so will
invalidate your
warranty.
Do noT point
grease gun at
yourself or other
persons or animals.
Do noT pull the
grease gun unit by
the hose.
Do noT use the
gun for a task it is
not designed to
perform.
Do noT operate
the gun when you
are tired or under
the influence of
alcohol, drugs or
intoxicating
medication.
When not in use,
clean the unit and
store in a dry, safe,
childproof area.
Original Language Version
cPG18V issue no.1 21/12/09
FUSE RATING 5AMP
Blue
Neutral
Wire
Yellow & Green
Earth Wire
Cable
Restraint
Brown
Live
Wire
