1. SAFETY
1.1.
GENERAL SAFETY
9
Disconnect the grinder from the mains power before changing accessories, servicing or performing any maintenance.
9
Maintain grinder and discs in good condition. Check moving parts and alignment. If necessary use an authorised service agent.
9
Replace or repair damaged parts. Use recommended parts only. Unauthorised parts may be dangerous and will invalidate the
warranty.
WARNING!
Always work with the grinder’s safety guard in place.
9
Wear approved safety goggles, ear defenders, gloves and, if grinder generates dust, a dust mask.
9
Position the power cable clear of the grinding wheel to avoid cutting or snagging it. Hold grinder only by insulated gripping surfaces.
9
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain long hair.
9
Use grinder in a suitable work area. Keep area clean, tidy and free from unrelated materials and ensure adequate lighting.
9
Maintain correct balance and footing,
DO NOT
over-reach. Ensure the floor is not slippery and wear non-slip shoes.
9
Use only approved grinding discs and only use the normal grinding surface.
9
Check grinding disc to ensure there are no splits, cracks or other damage (see Section 6). If in doubt
DO NOT
use the disc.
9
Grinding discs must be securely attached before use, but not over-tightened.
9
Secure unstable workpiece with a clamp, vice or other adequate holding device and ensure the grinder is gripped with both hands.
9
Keep non-essential persons away from the working area, use screens if necessary.
8
DO NOT
operate the grinder if any parts are missing or the grinder is damaged.
8
DO NOT
use the grinder for a task it is not designed to perform.
8
DO NOT
operate the grinder where there are flammable solids, liquids or gasses.
WARNING!
DO NOT
grind any materials containing asbestos.
8
DO NOT
get the grinder wet or use in damp or wet locations.
8
DO NOT
switch the grinder on whilst the disc is in contact with the workpiece.
8
DO NOT
cover the grinder air vents. To do so will overheat the machine.
8
DO NOT
touch the workpiece immediately after grinding, it will be very hot.
8
DO NOT
use the grinder as a fixed tool and
DO NOT
try to cool the grinding disc with water or other lubricants.
8
DO NOT
touch the grinding disc whilst operating, or whilst plugged into the mains power.
8
DO NOT
leave the grinder running unattended, and
DO NOT
lay the grinder down whilst it is running.
8
DO NOT
operate the grinder when you are tired or under the influence of alcohol, drugs or intoxicating medication.
9
When not in use switch off grinder, remove plug from power supply and store in safe, dry, childproof area.
9
Use only approved grinding discs and only use the normal grinding surface. Never use the side or upper surface of disc for cutting.
9
The grinding disc may only be changed by a person holding a grinding wheel certificate.
9
Grinding discs must be securely attached before use, but not overtightened.
2. INTRODUCTION
Compact, lightweight cordless mini angle grinder. Comfortable composite housing with soft grip to reduce vibration. Brushless motor allows
for a longer lasting tool requiring less maintenance. Spindle lock for easy disc changes. Built-in battery charge level indicator. Cutting disc not
included.
D
anger of fire/explosion hazard
WARNING!
The grinding process can produce streams of sparks which are a potential source of ignition, especially when
grinding metal.
8
DO NOT
use the grinder where there are flammable liquids, solids or gases.
8
DO NOT
allow grinder sparks to make contact with the operator’s clothing or any other fabric such as cleaning rags. Fabrics
contaminated with flammable materials such as petrol, oil, grease, paint and solvents are a particular fire hazard.
9
To reduce the risk of clothing catching fire the operator should wear wool or cotton outer garments treated with a fire retardant in
preference to man-made fibres.
12V Ø76MM ANGLE GRINDER - BODY ONLY
MODEL NO:
CP1210
T
hank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
CP1210 Issue 1 16/07/2020
Original Language Version
© Jack Sealey Limited
Refer to
instructions
Wear eye
protection
Wear protective
gloves
Wear ear
protection
Wear safety
footwear
Wear protective
clothing
Wear a mask
Wear
respiratory mask
(fumes)
