Ensure that the jack is in good working order. Take action for immediate repair or replacement of damaged parts.
Use genuine parts only. The use of unauthorised parts may be dangerous and will invalidate the warranty.
Locate the jack in a suitable, well lit work area.
Keep work area clean and tidy and free from unrelated materials.
Use jack on level and solid ground, preferably concrete.
Avoid tarmacadam as jack may sink in
.
Place chocks behind wheels of vehicle (
but ensure wheels of jack can move freely).
Ensure the vehicle handbrake is engaged, engine/motor is switched off and transmission is in gear or 'Park'.
Ensure minimum distance of 0.5m between vehicle and static objects such as doors, walls, etc., to allow for vehicle tilting.
Only place jack under those lifting points recommended by the vehicle manufacturer
(see vehicle handbook).
Ensure there are no passengers in the vehicle.
Ensure all non-essential persons keep a safe distance whilst the jack is in use.
Check the lifting point is stable and centred on the jack saddle.
Ensure the jack wheels are free to move and that there are no obstructions.
DANGER: Use the jack for lifting only, NOT for supporting the lifted load.
Ensure there are no persons or obstructions beneath the vehicle before lowering.
Use a qualified person to maintain or repair the jack hydraulic system.
DO NOT
operate the jack if you are tired or under the influence of alcohol, drugs or intoxicating medication.
DO NOT
operate the jack if damaged.
DO NOT
allow untrained persons to operate the jack.
DO NOT
exceed the rated capacity of the jack.
DO NOT
work under the vehicle until axle stands of suitable capacity have been correctly positioned.
DO NOT
use the jack for purposes other than that for which it is designed.
DO NOT
top up hydraulic system with brake fluid. Use hydraulic jack oil only. (Sealey Part No: HJO500MLS or HJO5LS)
DO NOT
adjust the safety overload valve.
DO NOT
jack vehicle if there is a risk of spillage of fuel, battery acid, or other dangerous substances.
DO NOT
allow the vehicle to move while supported by the jack and
DO NOT
use the jack to move the vehicle.
When not in use store jack, fully lowered, in a safe, dry, childproof area.
WARNING!
It is
very dangerous to go under a vehicle which is supported by a jack even if additional supports are used. DO NOT go under
a vehicle unless it is supported by adequately rated axle stands.
IMPORTANT! Ensure that you can see the saddle and jacking point throughout the jacking operation in case there is any relative
movement.
3.1.
Line up the holes in the two piece handle and fasten with the assembly screw.
3.2.
Loosen location bolt at the side of the handle base. Insert jack handle and tighten the bolt.
Your new Trolley Jack is produced and manufactured to a high standard of dependability and will, if used according to these instructions and
properly maintained, give you years of trouble free performance.
ImpORTANT: READ ThEsE INsTRucTIONs cAREfully. NOTE ThE sAfE OPERATIONAl REQuIREMENTs, WARNINGs AND cAuTIONs. usE
ThIs JAck cORREcTly AND WITh cARE fOR ThE PuRPOsE fOR WhIch IT Is INTENDED. fAIluRE TO DO sO MAy cAusE DAMAGE AND/OR
PERsONAl INJuRy AND WIll INvAlIDATE ThE WARRANTy. RETAIN ThEsE INsTRucTIONs fOR fuTuRE usE.
1. sAfETy PREcAuTIONs
3. AssEMBly
4.1. Before first use.
4.1.1. Before using the jack, purge hydraulic circuit in order to eliminate any air in the system
by turning the handle anti-clockwise to open, and pumping 8 or 9 times (fig.1).
4.1.2. Place a few drops of hydraulic jack oil on the pump piston and pump the handle several times
to distribute the oil. Thoroughly lubricate all moving parts.
4.2. General jacking.
WARNING! Before lifting ensure you read, understand and apply Section 1 safety
instructions.
4.2.1. Prepare the vehicle as mentioned in the safety instructions ensuring the ground on which
the jack is to stand is level and solid (not tarmacadam).
4.2.2. Position the jack saddle under the vehicle manufacturer’s recommended lifting point.
4.3. Jacking the vehicle.
4.3.1. Turn the handle clockwise to close the valve, pump the handle one full stroke and the “Rocket Lift” will raise the saddle sufficiently to
make contact with the vehicle’s jacking point. Once weight is on the saddle, the jack will operate conventionally. Continue pumping the
handle up and down using maximum strokes until the vehicle reaches the working height.
4.3.2. Should the jack become overloaded, a safety excess pressure valve will open, and stop the jack from lifting the vehicle further.
4.3.3. Once the required height is reached, place suitable capacity axle stands under the vehicle to support the load.
4. OPERATING INsTRucTIONs
fig.1
specification:
Capacity . . . . . . . . . . . . . . . . .3.2tonne
Max. Chassis Height. . . . . . . . . . . 163mm
Replacement Rubber Jack Pad. . . . . . . . . SSP223
Min. Saddle Height. . . . . . . . . .145mm
Length. . . . . . . . . . . . . . . . . . . . . 690mm
Max. Saddle Height . . . . . . . . . 504mm
Weight. . . . . . . . . . . . . . . . . . . . . . . . .36kg
2. INTRODucTION & sPEcIfIcATION
2.1.
Polyurethane wheels for increased manoeuvrability and prevents damage to workshop floor. Single piece hydraulic unit with heavy base
design. Integral American cog-type release mechanism and two-piece handle which is fitted with protective sleeve to help prevent
damage to vehicle bodywork during use. Super Rocket Lift feature brings lifting arm straight into contact with jacking point. Integral
saddle pads provides protection for the jacking point. Heavy-duty castor wheels and 55mm wide front wheels for even load distribution.
Original Language Version
3200CXQP Issue: 1 - 09/09/11
INSTRUCTIONS FOR:
TROllEy JAck 3.2TONNE
ROckET lIfT Pu WhEEls
MODEL No:
3200cXQP
