GSM-R4-DIN_EN (Version 1.02; 2016-04-06)
Page #1 of 5
GSM-R4-DIN, GSM-R4-DINB
1.
Introduction
The
GSM-R4-DIN
and
GSM-R4-DINB
(
GSM
rele
4
for short)
are designed to be
mounted on a DIN rail into a switchboard.
GSM
rele
4
can control two
independent electrical circuits in a building e.g. circuit of an accumulator stove and
circuit for garage gate control. The control is made via SMS messages or by ringing.
After installation into an electrical box insert a SIM card of any GSM operator and the
device is ready to operate.
GSM
rele
4
has
2 galvanically isolated digital outputs
with a semiconductor
switch, which can control directly low power circuits up to 230V
AC
/90mA. It’s possible
to control directly e.g. a thermoregulator circuit of a gas boiler or a coil of one phase
contactor 230V AC. The contact of the contactor can then control either one phase
high power appliance (e.g. electrical radiator) or a coil of three phase contactor of an
accumulation stove.
GSM
rele
4
has also
2 analog inputs
for temperature measuring and
2 digital
inputs
which can be activated by a contact from 4V power provided by
GSM
rele
4
or
by an external voltage 3 to 30V DC.
GSM
rele
4
has built in two
automatic
regulators
which use analog inputs from temperature sensors to maintain preset
temperature. The temperature of sensors can be readout via SMS.
There is an internal
built in Li-Ion accumulator
which enables to send an SMS in
case of a power failure and to restore the output status after a power failure. It’s also
possible to monitor the status of inputs and temperatures via SMS during 230 V
AC
power failure.
(1) OUTPUT 3, 4 (Y3, Y4) connectors
(2) Pushb LED (Y3, Y4)
(3) INPUT 1, 2 (X1, X2) LED
(4) INPUT 1, 2 (X1, X2) connectors
(5) DIN rail holder
(6) Temperature sensors connector (T5, T6)
(7) USB connector (for configuration)
(8)
GSM
rele
4
operation state LED indicators
(9) 230V
AC
Power supply connector
(10) SIM card and MicroSD card holder
(11) External GSM antenna connector
( - ) Temperature sensor GSM-C-T2
2.
Package Content
1 pc
GSM
rele
4
(order code
GSM-R4-DIN
or
GSM-R4-DINB
)
1 pc GSM antenna ANT05S
1 pc temperature sensor GSM-C-T2 (based on KTY81-210), cable - 1 meter
1 pc cable USB 2.0 A-B, 1.8m (order code HW-11.02.8818)
1 pc connector 5.00 mm
2 pcs connector 3.81 mm
1 pc connector 3.81 mm
1 pc connector 3.81 mm
1 pc screwdriver 2 mm
1 pc printed documentation
3.
Installation
1.
To operate the
GSM
rele
4
a SIM card of any GSM operator is necessary. SIM card
must be functional and active. Also some credit is necessary if SIM card is pre-
paid. We recommend to deactivate the PIN code for installation.
2.
Insert this prepared SIM card (cut off corner first) into a slot on the side of the
GSM
rele
4
. The SIM card holder is located in a slot on side of
GSM
rele
4
(close to
GSM antenna connector). The proper insertion is indicated by a slight mechanical
click noise. To remove the SIM card - press the SIM card in direction into the
GSM
rele
4
until mechanical click. The SIM card can be the freely removed.
3.
Now it’s possible to connect the device to 230V AC power supply. If the power
supply is correct, green LED diode
POWER SUPPLY
goes on. After about 20
seconds, blue LED diode GSM starts flashing with a period 1 per 3 sec.
4.
For the first tests of
GSM
rele
4
the connection of inputs and outputs is not
important. Please keep in mind that the devices connected to OUTPUTS will be
switched on during tests!
5.
To test the
GSM
rele
4
press the pushbutton bellow OUTPUT 3. The green LED
diode for OUTPUT 3 lights ON. Send an SMS from mobile phone (which will be
mainly used to control the
GSM
rele
4
) in form
1234 Y3 OFF
to the telephone
number of the SIM card inserted into the
GSM
rele
4
. This will switch off the
plugged appliance. The green status LED for OUTPUT3 goes OFF. Simultaneously,
the device automatically sends a confirmation SMS message on performing the
operation. The password 1234 can be changed later in configuration. The
GSM
rele
4
reacts on the SMS text message from any telephone as long as the
access password matches. The very first one (the sender of the first valid SMS
message) will be remembered as master and will receive messages about events
on
GSM
rele
4
. This user can also control OUTPUT 4 by “ringing” on the device.
6.
Try “ringing” on device. You can make pulse on OUTPUT 4 for approx. 4 seconds
by calling to
GSM
rele
4
(with default factory setting). The device hangs up the call
and makes pulse on the OUTPUT 4. This pulse can be used for example for
opening entrance gate. To test this function call from the phone (which was used
to send the first test SMS to switch off the OUTPUT 3). The pulse is indicated by
green LED.
7.
Try regulation. You can send SMS in form of
1234 Y3 REG 25
to command the
device to maintain temperature to 25°C. The range of regulation is between 0°C
and +55°C. Regulation can be canceled by SMS with command
1234 Y3 OFF
. By
default the regulation of OUTPUT 3 depends on temperature sensor connected to
analog INPUT T5 (OUTPUT 4 depends on INPUT T6).
8.
A default factory setting of the
GSM
rele
4
can be recovered by an SMS in form
1234 FACTORY.
Your setting can be then restored from backup configuration of
SeaConfigurator
program.
4.
Technical specifications
Parameter
Symbol
MIN.
TYP.
MAX.
Unit
Dimensions
Width
Š
71
mm
Height
V
90
mm
Depth
H
58
mm
Power
supply
*1)
Voltage
V
180
230
250
V AC
Current
11
30
mA
Digital inputs
INPUT1, INPUT2
Voltage
V
IN
3
12
30
V DC
Current
I
IN
3,5
mA DC
Digital
outputs
OUTPUT3, OUTPUT4 - Semiconductor switch OPTO-MOS
Voltage
V
OUT
5
230
260
(400)
V AC
(V DC)
Current
I
OUT
90
(120)
mA AC
(mA DC)
Analog inputs
2 x temperature sensor GSM-C-T2, Accuracy in range 0 to 30°C ... 1°C
Temperature
-
-30
+55
°C
Temperature
Storage
without supply
3
*2)
Months
Operational
tA
-20
+45
°C
Use
GSM
rele
4
- DIN inside the rack with IP44 or better!
!
*1)
Use breaker max. 10 A before
GSM
rele
4
. For power supply 230V
AC
use lines min.
1 mm
2
.
*2)
The
GSM
rele
4
has to be connected to 230V
AC
power supply every 3 months for
24 hours (due to internal accumulator).
5.
Hardware
The front panel of the
GSM
rele
4
contains a set of status indicating LED
diodes located, pushbuttons for local
control of outputs, connectors for
connecting power supply, input signals,
output
signals
and
temperature
sensors.
5.1
Connectors
GSM
rele
4
enables to connect 2
external digital inputs, 2 external digital
outputs and 2 external temperature
sensors GSM-C-T2 with temperature
range from -30°C to +55°C.
The line length of a connected external
temperature sensor is not limited but
the wire has a certain resistance which
influences the measured temperature (16 means 1 °C).
The recommended type of relay for connection of more appliances is GSM-RELE-OUT.
When using the
GSM
rele
4
for a gate control by a phone ring, it’s possible to connect
output 3 and COM directly with a pushbutton of the gate control.
Read
Technical specifications
before connecting external devices! Don’t overload
inputs and outputs.
Examples of connection of
GSM
rele
4
are placed later in this text.
5.2
Pushbuttons
The
GSM
rele
4
has two pushbuttons for local control of outputs. Every press of the
pushbutton changes the state of the output.
Before inserting the SIM card into the
GSM
rele
4
device, we
recommend to turn off setting of the “PIN code”!
Insert the active SIM card (= at least one call was made) to any mobile
telephone and turn off the requirement of setting the PIN. On most mobile
telephones, this option can be found in menu “Setting the telephone
protection”. or “Setup -> Security -> PIN control”.
ATTENTION:
GSM
rele
4
must be mounted by qualified personnel only!
X2 4V
X1
230 V
AC
GND
POWER
ERROR
GSM
rele
4
3
4
ALARM
GSM
1
2
1 2 3
4 5
6
GSM
ANT.
Y3
Y4
T5
T6
1 2 3
4
1 2
1 2
1
2
L1
N
EXT
USB
SIM,
uSD
3
1
2
8
9
6
11
4
7
5
5
10
