background image

Page 1 of 44

P/N 595189-01  Rev A  4/10

TYPICAL SKA-PAK AT WITH STANDARD HARNESS 

REAR VIEW

TYPICAL SKA-PAK AT WITH STANDARD HARNESS

FRONT VIEW

Scott SKA-PAK AT units may vary in appearance, accessories and options.

OPERATING & MAINTENANCE INSTRUCTIONS

Airline 

connecTion 

hoSe

hoSe from

PreSSure

reducer To 

breAThing 

regulATor

cylinder 

And vAlve 

ASSembly

Shoulder 

STrAP

Airline 

connecTion 

hoSe

PreSSure 

reducer

heAd 

hArneSS

cylinder 

vAlve Knob

breAThing 

regulATor 

WiTh vibrAlerT

hoSe from

 PreSSure reducer 

To breAThing 

regulATor

SKA-PAK

®

 AT 

AuTo TrAnSfer

COMBINATION SELF-CONTAINED BREATHING APPARATUS 

FOR ESCAPE AND PRESSURE DEMAND TYPE C

 SUPPLIED-AIR RESPIRATOR WITH AUTO TRANSFER

fAcePiece

PreSSure gAuge 

WiTh elecTronic 

AlArm

WArning

imProPer  uSe  of  ThiS  reSPirATor  mAy  reSulT  in  PerSonAl  inJury  or  deATh. 

imProPer uSe includeS, buT iS noT limiTed To, uSe WiThouT AdeQuATe TrAining, 

diSregArd  of  The  WArningS  And  inSTrucTionS  conTAined  herein,  And  fAilure 

To  inSPecT  And  mAinTAin  ThiS  reSPirATor.
ThiS  reSPirATor  iS  inTended  To  be  uSed  only  in  conJuncTion  WiTh  An  orgAniZed 

reSPirATory  ProTecTion  ProgrAm  Which  comPlieS  WiTh  The  reQuiremenTS  of 

"PrAcTiceS for reSPirATory ProTecTion," Z88.2 AvAilAble from AmericAn nATionAl 

STAndArdS inSTiTuTe inc., 1430 broAdWAy, neW yorK, n.y., 10018; or The reQuiremenTS 

of oShA SAfeTy And heAlTh STAndArd 29 cfr 1910 PArAgrAPh 134 AvAilAble from The 

u.  S.  dePArTmenT  of  lAbor,  occuPATionAl  SAfeTy  And  heAlTh  AdminiSTrATion;  or 

oTher  PerTinenT  nATionAlly  recogniZed  STAndArdS,  Such  AS  ThoSe  PromulgATed 

by The uS coAST guArd or The dePArTmenT of defenSe.

COPYRIGHT ® 2010, SCOTT, All Rights Reserved

Summary of Contents for SKA-PAK AT













































Reviews: