Scotsman CME456R Product Manual Download | Manualshive

Page: 1 / 36

background image

Introduction

This product manual contains the information

needed for the setup, installation, initial start up,

sanitation and maintenance of this ice machine.

Keep it for future reference.
Be certain that the information applies to the model

in question. If no model is listed, the information

applies to all models.

This manual is organized in the same way as the

expected use of the machine, it begins with

specifications, goes thru unpacking and setup,

shows where everything is; continues with initial

start up, then describes how it works. After that is

the sanitation section, followed by service

diagnosis and repair.

CME456R

December 2000

Page 1

Parts Lists and Wiring Diagrams are in the section at the center of this manual.

Table of Contents

Specifications . . . . . . . . . . . . . . Page 2
Condenser and Ice Machine Layouts . . Page 3
Pre-Installation . . . . . . . . . . . . . . Page 4
Location & Assembly . . . . . . . . . . . Page 5
Bin Control: Optional Installation . . . . . Page 6
For The Installer: Remote Condenser . . Page 7
Remote Condenser Location . . . . . . Page 8
Coupling Instructions . . . . . . . . . . . Page 9
Fan Relay Kit . . . . . . . . . . . . . . Page 10
Electrical . . . . . . . . . . . . . . . . Page 11
Plumbing . . . . . . . . . . . . . . . . Page 12
After Utility Connections . . . . . . . . Page 13
Component Location and Function . . . Page 14
AutoIQ Controller . . . . . . . . . . . . Page 15
Initial Start Up . . . . . . . . . . . . . . Page 16
Adjustments . . . . . . . . . . . . . . Page 17
How To Operate The AutoIQ Controller Page 18
How The Electronic Cuber Works . . . Page 19
How The Electronic Cuber Works . . . Page 20
Technicians Only: Freeze Cycle Sequence . . .

. . . . . . . . . . . . . . . . . . . . . . Page 21

Technicians Only: Harvest Cycle Sequence & Other

Notes . . . . . . . . . . . . . . . . . . Page 22
Sanitation and Cleaning . . . . . . . . Page 23
Additional Maintenance . . . . . . . . . Page 24
Additional Maintenance: Inlet Water Valve Screen

. . . . . . . . . . . . . . . . . . . . . . Page 25

Additional Maintenance: Ice Sensors, Condenser

. . . . . . . . . . . . . . . . . . . . . . Page 26

Service Diagnosis: Diagnostic Light Analysis

.

. . . . . . . . . . . . . . . . . . . . . . Page 27

Service Diagnosis . . . . . . . . . . . Page 28
Service Diagnosis: Components . . . . Page 29
Service Diagnosis . . . . . . . . . . . Page 30
Operational Characteristics:

CME456R

Page 31

Removal and Replacement . . . . . . . Page 32
Removal and Replacement: AutoIQ Controller .

. . . . . . . . . . . . . . . . . . . . . . Page 33

Removal and Replacement: Water Level Sensor

. . . . . . . . . . . . . . . . . . . . . . Page 34

Refrigerant . . . . . . . . . . . . . . . Page 35
Before Calling for Service . . . . . . . Page 36

1
2
3
...
»

Summary of Contents for CME456R





































Reviews:

No comments

Related manuals for CME456R

PrimaDonna Exclusive

Brand: DèLonghi Pages: 11

Brand: Oster Pages: 46

Coffe Center 5500

Brand: DeLonghi Pages: 18

Brand: Meijer Pages: 8

Multiplex MS-8-1H

Brand: Multiplex Pages: 24

Brand: Faema Pages: 28

Brand: Capresso Pages: 2

Brand: Gaggia Pages: 76

Brand: Bunn Pages: 9

SOFT SERVEIC13886

Brand: Hershey's Pages: 7

Elektronika II Prof

Brand: ECM Pages: 33

BELGIAN PRO NeverStick

Brand: Ninja Pages: 9

Brand: GE Pages: 72

Brand: Royal Pages: 11

Brand: NewAir Pages: 34

Brand: Argox Pages: 92

Brand: Blueair Pages: 47

Brand: Franklin Chef Pages: 92

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands