schmersal AZM300B-I2-ST-SD2P Instructions Manual Download

Page: 1 / 30

INSTRUCTIONS FOR OPERATION AND
ASSEMBLY
SOLENOID INTERLOCK AZM300B-I2-ST-
SD2P

Table of Contents

1.1 Function
1.2 Target group of the operating instructions: authorised qualified personnel
1.3 Explanation of the symbols used
1.4 Appropriate use
1.5 General safety instructions

2 Product description

2.1 Ordering code
2.2 Special versions
2.3 Purpose
2.4 Warning about misuse
2.5 Exclusion of liability
2.6 Technical Data

3 Mounting

3.1 General mounting instructions
3.2 Manual release
3.3 Emergency exit -T/-T8 or emergency release -N
3.4 Mounting with mounting plate
3.5 Dimensions
3.6 Actuator and accessories

4 Electrical connection

4.1 General information for electrical connection
4.2 Serial diagnostic -SD
4.3 Wiring examples for series-wiring
4.4 Wiring configuration and connector accessories

5 Actuator coding and latching force adjustment

5.1 Actuator coding
5.2 Latching force adjustment

6 Active principle and diagnostic functions

6.1 Magnet control
6.2 Mode of operation of the safety outputs
6.3 Diagnostic-LEDs
6.4 Solenoid interlock with conventional diagnostic output
6.5 Solenoid interlock with serial diagnostic function SD

7 Set-up and maintenance
8 Disassembly and disposal

Summary of Contents for AZM300B-I2-ST-SD2P































Search results

Summary of Contents for AZM300B-I2-ST-SD2P

Reviews:

Related manuals for AZM300B-I2-ST-SD2P

Brands by name

Popular brands

schmersal AZM300B-I2-ST-SD2P, Instructions Manual

Search results

Summary of Contents for AZM300B-I2-ST-SD2P

Reviews:

Related manuals for AZM300B-I2-ST-SD2P

Brands by name

Popular brands