background image

HDMI

VIDEO INPUT

2

HDMI

1

(DVI)

(DVI AUDIO)

(VIDEO)

The American Academy of Pediatrics dis-
courages media use by children younger
than two years. For more information,
visit www.aap.org.

Please read before operating your HDTV!

PROTECTING THE LCD
SCREEN

CAUTION: 

The screen can be damaged if
it is not maintained properly. 

• Do not use hard objects such as hard

cloth or paper to clean the screen.

• Do not use excessive pressure when

cleaning the screen; excessive pressure
can cause permanent discoloration or
dark spots.

NEVER

spray liquids on the screen.

HANDLING PRECAUTIONS

• Handle by the cabinet only. 

• Handling by two or more people is rec-

ommended.

• Never touch the screen when handling.

• Handling damage is 

not

covered under

warranty.

• Do not remove the protective film 

covering the front cabinet while 
handling the HDTV.

POSITIONING THE HDTV 

• Always use a firm and flat surface when

positioning your HDTV. 

• Do not position the unit in a confined

area. 

• Allow adequate space for proper venti-

lation.

• Do not position the HDTV where it is

easily reachable by small children and
may present risk of injury.

• Once HDTV is positioned, remove the

protective film covering front cabinet.

SPECIFICATIONS

NOTE: Design and specifications are
subject to change without notice.

Power Requirement:

Source: AC 120V, 60Hz

AC Power Consumption:

155 watts

Weight:

48.1 lbs  (w/stand)

Dimensions _________________________

WIDTH    HEIGHT   DEPTH

w/stands

51.3

31.5

10.5

w/out stands

51.3

30.4

3.9

NOTE: Dimensions are in inches

SANYO television cus-
tomers should contact MRM
Recycling at 888-769-0149 or
visit their website at
www.mrmrecycling.com
regarding SANYO’s waste
management plan.

NOTE: Skip these steps if using a wall

mounting kit (not included).

1

Place HDTV face down on a
padded or cushioned flat surface
to protect the screen and finish.

2

Carefully insert both foot stands to
the bottom of the HDTV and secure
them by inserting two (2) long
screws (M4 4x30) in each one as
indicated in the diagram below.

NOTE: Foot stand screws are located in

the literature package.

3

Position the HDTV on a firm and
flat surface with adequate space
for proper ventilation.

STAND ASSE

M

BLY

______

GETTING STARTED

Hook up your antenna or your cable
service to the HDTV’s 

ANT

terminal

with the use of a 75 OHM coaxial cable.

NOTE: Keep your indoor antenna at

least 3 ft. away from the televi-
sion set and any other electron-
ic equipment.

The tuner in this HDTV can receive

:

• 

Digital and Analog off air signals
from an antenna

• 

Analog or ClearQAM cable channels
from a direct Cable TV connection.

ANTENNA CONNECTION FOR
OFF-AIR SIGNALS OR CABLE

ANTENNA

CABLE

ANALOG / DIGITAL

ANTENNA IN

AV INPUT SELECTION

Press the 

INPUT

key to select the 

correct AV input for the video source
you wish to watch.

NOTE: Unused AV inputs may be dis-
abled with the Input Setting feature.

Finish Setup

Repeat

Channel Search Result: Succesfully Completed

If you are having problems, call us toll-free at 1-800-877-5032

Analog Channels

Video

HDMI 1

HDMI 2

Digital Channels

16

26

HDMI 3

Before proceeding, please make
sure to correctly hook up your
antenna or cable connection and
all AV equipment to your HDTV.

1. PLUG IN AC POWER CORD

120V AC, 60Hz

2. TURN ON TV

3. TV SET LOCATION SELECTION:

Select “

Home Mode

” to set the

HDTV’s backlight to an Energy Star
qualified level, or select “

Store

Mode

” to set the backlight to a retail

display level.

4. CHANNEL AND SIGNAL SEARCH:

Select “

Signal Search

” and press

ENTER

to perform a channel search

from an Antenna or a direct Cable
connection, and a signal search
from devices hooked up to the
HDTV’s AV input jacks.

5. SIGNAL SEARCH RESULT SCREEN

The final setup screen displays ana-
log and digital channels found, as
well as AV inputs detected.

Select 

Finish Setup

and press

ENTER

.

NOTE: If  you wish to repeat the

process, select Repeat.

INITIAL CHANNEL SEARCH

Need help? 

www.sanyoctv.com              1-800-877-5032

Need help? 

www.sanyoctv.com              1-800-877-5032

1JC0P1P0041- -

Part No.:

Owner’s 

Manual

(English)

© 2013 Sanyo Manufacturing Corporation

1080p HDTV LCD

58”

LED

class

(57.5” diagonal)

Model:

DP58D33

1080p HDTV LCD

As an Energy Star

®

Partner, Sanyo

Manufacturing Corporation has
determined that this product
meets the Energy Star

®

guidelines

for energy efficiency.

ENERGY STAR

TRADE

M

ARKS

________

Manufactured under license from Dolby
Laboratories. “Dolby” is a trademark of
Dolby Laboratories.

HDMI, the HDMI Logo and High-Definition
Multimedia Interface are trademarks or regis-
tered trademarks of HDMI Licensing LLC in
the United States and other countries.

HDTV INPUT/OUTPUT REFERENCE ________________________________________

HDTV SIDE PANEL

1

ANT Analog / Digital Antenna Input

Hook up your indoor or outdoor digital antenna, or a direct
Cable service (Analog or ClearQAM).

VIDEO INPUT (CO

M

PONENT/CO

M

POSITE combo)

CO

M

POSITE Connection

A Composite connection is used to hookup your analog
equipment such as a VCR or an older DVD player.

Match the YELLOW connector from your external device to
the GREEN Y-VIDEO jack on the HDTV.

NOTE: Use the WHITE and RED (L and R) jacks for AUDIO

signal.

CO

M

PONENT Connection

A Component connection will accept SDTV, EDTV and
HDTV video signals. Use it for great image quality from di-
gital devices such as a DVD player or Video Game system.

Match your digital device’s Component output jacks to the
Component input jack set on your HDTV.

NOTE: Use the GREEN (Y), BLUE (Pb) and RED (Pr) jacks for the

VIDEO signal and the WHITE and RED (L and R) jacks for
the AUDIO signal.

HD

M

I (INPUT1 or INPUT2)

Use 

HD

M

I INPUT1 & 2

to hookup HD digital devices such as

a Blu-ray player, HD Cable Box, HD Satellite Receiver or
Video-game System.
Connect your digital device’s HDMI output to any of the two
(2) HDMI inputs on your HDTV’s side panel with the use of
an HDMI cable.

NOTE: A DVI connection is possible via the HDMI (DVI) INPUT1

using an appropriate cable or adapter and connecting the
audio to the L and R (VIDEO INPUT) jacks.

USB

USB 

input jack is used to connect a USB mass storage

device to watch digital images stored in JPEG format.

DIGITAL AUDIO OUT (Coaxial)

Hookup a multichannel receiver with the use of a phono-
type digital audio cable.

HD

M

I (INPUT3)

Use 

HD

M

I INPUT3

to hookup HD digital devices such as a

Blu-ray player, HD Cable Box, HD Satellite Receiver or
Video-game System.
Connect your digital device’s HDMI output to the HDMI3
input on your HDTV with the use of an HDMI cable.

1

2

3

4

5

6

Printed in Mexico, January 2013

US3B  /  58-Z7GB  /  GXHA

Sanyo 

M

anufacturing Corp. 3333

Sanyo Road, Forrest City, AR 72335

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance

with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat

registers, stoves, or other apparatus (including amplifiers) that
produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-

type plug. A polarized plug has two blades with one wider than
the other. A grounding-type plug has two blades and a third
grounding prong. The wide blade or the third prong are provided
for your safety. If the provided plug does not fit fully into your out-
let, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched par-

ticularly at plugs, convenience receptacles, and the point
where they exit from the apparatus.

11. Only use attachments/accessories specified by the 

manufacturer.

12. Use only with the cart, stand, tripod, bracket,

or table specified by the manufacturer, or sold
with the apparatus. When a cart is used, use
caution when moving the cart/apparatus
combination to avoid injury from tip-over.

13.  Unplug this apparatus during lightning storms or when unused

for long periods of time.

14. Refer all servicing to qualified service personnel. Servicing is

required when the apparatus has been damaged in any way,
such as power-supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does not operate nor-
mally, or has been dropped.

15. If an outside antenna is connected to the television equipment,

be sure the antenna system is grounded so as to provide some
protection against voltage surges and built up static charges.
In the U.S. Selection 810-21 of the National Electrical Code pro-
vides information with respect to proper grounding of the mast
and supporting structure, grounding of the lead-in wire to an
antenna discharge unit, size of grounding conductors, location
of antenna discharge unit, connection to grounding electrodes,
and requirements for the grounding electrodes.

16. An outside antenna system should not be located in the vicini-

ty of overhead power lines or other electrical light or power
circuits, or where it can fall into such power lines or circuits.
When installing an outside antenna system, extreme care
should be taken to keep from touching such power lines or cir-
cuits as contact with them might be fatal.

EXAMPLE OF ANTENNA GROUNDING ACCORDING
TO NATIONAL ELECTRICAL CODE, ANSI/NFPA 70

“Note to CATV system installer:
This reminder is provided to call the CATV system installer’s
attention to Article 820-40 of the NEC that provides guidelines for
proper grounding and, in particular, specifies that the cable
ground shall be connected to the grounding system of the build-
ing, as close to the point of cable entry as practical.”

17. Wall or Ceiling Mounting—The product should be mounted to

a wall or ceiling only as recommended by the manufacturer.

18. Apparatus shall not be exposed to dripping or splashing, and no

objects filled with liquids, such as vases, shall be placed on it.

19. When the MAINS plug is used as the disconnect device, the

disconnect device shall remain readily operable.

RISK OF ELECTRIC SHOCK   DO NOT OPEN!

CAUTION: TO REDUCE RISK OF ELECTRIC SHOCK, DO NOT RE

M

OVE COVER (OR BACK). NO

USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

THIS SYMBOL INDICATES THAT DANGEROUS VOLTAGE CONSTITUTING A RISK
OF ELECTRIC SHOCK IS PRESENT WITHIN THIS UNIT.

THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT OPERATING AND MAINTE-
NANCE INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THIS UNIT.

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR 

M

OISTURE.

I

M

PORTANT SAFETY INSTRUCTIONS

CAUTION

FCC INFOR

M

ATION

________________________________________________

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation.  This equipment gen-
erates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harm-
ful interference to radio communications.  However, there is no guarantee that interference will not occur in a particular installation.  If
this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following  measures:  

– Reorient or relocate the receiving antenna.  

– Increase the separation between the equipment and receiver.  

– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  

– Consult the dealer or an experienced radio/TV technician for help.

CAUTION

: FCC Regulations state that improper modifications or unauthorized changes to this unit may void the user’s authority to 

operate the unit.

This equipment is a Class II or double insulated electrical appliance. It has been designed in such a way that it does not require

a safety connection to electrical earth.

Install two (2) “AAA” batteries in the
remote control. (Not included)

PRECAUTIONS:

• Replace both batteries at the same

time. Do not use a new battery with a
used battery. 

• There’s a risk of explosion if a battery

is replaced by an incorrect type.

• Keep away from moisture.

• Be sure to match the 

“+”

and 

“–”

signs on the batteries with marks
inside the remote control.

• Please properly dispose of used up

batteries.

WARNING: 

The batteries (or battery

pack) shall not be exposed to excessive
heat such as sunshine, fire or the like.

BATTERY INSTALLATION

ENERGY STAR is a set of power-saving guidelines issued by the U.S. Environmental Protection

Agency (EPA). ENERGY STAR is a joint program of the U.S. Environmental Protection Agency and

the U.S. Department of Energy helping us all save money and protect the environment through

energy efficient products and practices.

Changes to default as-shipped television configuration and settings or enabling certain optional

features and functionalities will change the energy consumption of the television, this may

increase energy consumption beyond the limits required for ENERGY STAR qualification.

2

3

HDMI

3

DIGITAL

AUDIO OUT

HDTV BACK PANEL

5

6

4

WALL 

M

OUNTING

(OPTIONAL)

Wall mounting of the HDTV must be
performed by a skilled person.

If foot stand disassembly is required:

• Place HDTV face down on a padded or

cushioned flat surface to protect the
screen and finish.

• Remove the two (2) screws securing

each foot stand. 

CAUTION:

Hold the

stands firmly as you remove the last
screw.

Use the four (4) short screws
included in the literature package
to secure the HDTV to a wall
mounting kit (not included.)

I

M

PORTANT: Wall mount kit must

comply with VESA standard 400 x
400. All four (4) screws must be
threaded to the wall mount and
HDTV’s back cabinet

M

ounting screws measurements: 

M6 (6mm) Diameter, Length 12mm
(min.) – 16mm (max.)

Reviews: