M
uch like the AV jacks, the SIDE/AV jacks allow for extra accessory
device connections for items such as cameras or gaming stations.
The SIDE/AV Input Jacks are located on the rear of the TV.
NP
1
Connect the VIDEO (yellow) adapter cable to the VIDEO AV2 in jack
on the side of the TV. Connect the other end of the VIDEO (yellow)
cable to an RCA type VIDEO Cable. Connect that cable to the VIDEO
OUT jack on the back of the accessory device being used. Note: An
S-Video cable can be used in place of the S-Video cable if your
device is equiped with an S-Video Output. S-Video provides better
video playback.
2
Connect the AUDIO (red and white) adapter cableto an RCA type Audio
Cable. Connect the other ends of the AUDIO (red and white) cables to
the AUDIO (left and right) OUT jacks on the rear of the accessory device
being used.
3
Turn the accessory device and the TV ON.
4
Press the SOURCE button on the remote control to show the Source menu
on the CVBS side or S-Video side under AV2 mode.
5
With the accessory device ON, press the PLY button to activate the playback
on the television.
PC with VGA
OUTPUT
R
L
E
A
R
P
H
O
N
E
S
VID
EO
－
VID
EO
－
（
）
RS 232C
FOR UPDATE
／
ANT
ATSC NTSC
DVI INPUT
L R
／
PC INPUT
VGA
L R
／
AV
3 COMPONENT INPUT
Y
Pb Cb
／
Pr Cr
／
R
L
AV
4 COMPONENT INPUT
Y
Pb Cb
／
Pr Cr
／
R
L
S VIDEO
－
AV1
INPUT
VIDEO
R
L
AV1
INPUT
VIDEO
R
L
AV
INPUT
VGA
B
ASIC
TV O
PERATION
First, assemble the TV using the steps below:
T
ELEVISION
This television has a set of controls located on the side of the cabinet for use when the
remote control is not needed.
R
EMOTE
C
ONTROL
B
UTTONS
PC (M
ONITOR
) I
NPUTS
H
OOKING
U
P THE
T
ELEVISION
SIDE/AV I
NPUTS
H
EADPHONE
C
ONNECTIONS
VGA
CABLE
HEADPHONE CABLE
1
2
3
C
Jack Panel Bottom of TV
AV2
CVBS SIDE
OR
AV2
S-VIDEO SIDE
2
DVI CABLE
PC with DVI
OUTPUT
PC -D
OR
To PC
AUDIO IN
En
g
lis
h
Quick Setup Guide
B
4
R
L
E
A
R
P
H
O
N
E
S
VID
EO
－
VID
EO
OR
R
L
E
A
R
P
H
O
N
E
S
VID
EO
－
VID
EO
2
⑦
⑥
⑤
④
③
②
①
- CH +
- VOL +
MENU MODE
①
IR: Remote Control Sensor
②
Power switch: Press to power on or power off the TV set.
③
●
LED: Power Indicator.
④
MODE
Mode: Press to select input signal modes or use as Enter in Menu operation.
⑤
MENU
Menu: Press to enter Menu or exit Menu.
⑥
- VOL +
Left: Press to decrease the sound volume level or move Left in Menu operation.
Right: Press to increase the sound volume level or move Right in Menu operation.
⑦
- CH +
Down: Press to select the next lower Programme number or move Down in Menu operation.
Up: Press to select the next higher Programme number or move up in Menu operation.
C
ONTENTS
Important Notice/Warning
........................................
1
Stand Assembly
...........................................................
1
Basic TV Operation
......................................................
1
Remote Control Button Descriptions
.....................
1
Hooking up the Television
Remote Control Battery Installation.........................
2
Basic Cable/Cable Box TV Connections..................
2
Basic Antenna TV Connections.................................
2
AV Input Connections
................................................
3
Component Video Input Connections
.................
3
High Definition Input Connections
........................
3
PC (Monitor) Input Connections
.............................
4
Rear/SVHS Input Connections
.................................
4
Headphone Connections
...........................................
4
IMPORTANT
NOTE:This owner’s manual is used with several different
television models. Not all features(and drawings) discussed
in this manual will necessarily match those found with your
television set. This is normal and does not require that you
contact your dealer or request service.
WARNING: TO PREVENT FIRE OR SHOCK HAZARD DO
NOT EXPOSE THIS UNIT TO RAIN OR EXCESSIVE
MOISTURE.
A
T
his TV can be used as a PC Monitor. Your computer will
have to be equipped with a VGA (or DVI type video output)
and VGA cable (or a DVI cable).
.
1
Connect one end of the VGA Video cable to the Monitor
(video) output on the computer to the VGA jack
on the bottom of the TV.
OR
if your computer comes with DVI video output, you can
use a DVI cable to connect from the computer's
DVI output to the PC-D input on the bottom of the TV.
2
The TV can reproduce the computer's audio. Using a 3.5mm
Stereo Plug cable, connect the Stereo plug
to the Audio output jack on the computer (if available) while
connecting the PC AUDIO IN on the bottom of the TV.
.
3
Turn the TV and the computer ON.
4
Press the source button on the remote control to show the
SOURCE
menu on VGA or DVI mode.
The eadphone jack can be used to connect to a headphone. If connected
to a headphone, there will be no sound from the TV speakers. The sound
will come fom the audio system of the headphone.
1
Connect Headphone jack located on the right rear of the TV to your
headphone set.
2
Turn the TV and headphone ON. TV sound can be heard through the
headphone.
2
3
5
4
1
1
1
3
1
4
“
POWER
”
To switch TV set between
power on and standby modes.
“
MUTE
”
To mute the audio output.
“
MENU
”
To enter Menu mode.
“
ENTER
”
To enter sub Menu or sub
item.
“
MTS
”
To select audio program
options.
“
CC
”
To select close caption options
(CC1, CC2 ...)
“
VOL- ( )/ VOL+( )
”
To decrease or increase the
sound volume. Also to navigate
left or right the Menu.
“
0~9 number
”
To enter TV channel
number.
“
LAST
”
To switch to the previously
viewed channel.
“
EPG
”
To enter or exit Electronic
Program Guide.
“
SOURCE
”
To select input source.
“
SLEEP
”
To Adjust sleep timer options.
“
•(dot)
”
To enter sub channel number.
“
CH+ ( )/ CH – ( )
”
To select the next higher or
lower channel. Also to navigate
up or down the Menu.
“
Exit
”
To exit Menu or other OSD.
