Mortise Lock: SALTO
LA1T05xx../LA1T15xx..
BA
C
K
SE
T
2
-3
/4
"
(7
0 M
M
)
(A
X
E)
1-
3/
4"
(
45
m
m
)
2
2
1
3
7
8
T
e
m
p
la
te
4-
1/
2"
(1
14
m
m
)
LOCK INSTALLATION Electronic escutcheon Mortise locksets
PREPARING THE DOOR
Note: if the strike already exists in the door frame, position lock using strike as
reference.
(See strike position on template)
1.
Draw horizontal line on both sides and edge of door at the desired
height of knob above floor.
2.
Draw vertical center line on door edge.
3.
Draw vertical line on each side at the proper backset to align the
template.
4.
Position templates on edge and sides of door.
Mark holes ONLY for each side, and top and bottom holes of mortise
cavity on door edge, and holes in the lateral face of the door for
handles, turn piece hole (only needed in inside face).
5.
If lock has anti-friction latch, mark proper recess area on door edge
template. (See lock body to determine proper side.)
6.
Remove template: place lock face against door edge.
Trace outline of faceplate as guide for faceplate routing.
MORTISE THE DOOR
1.
Mortise door for lock body and faceplate per instructions on template.
INSTALLING THE LOCK BODY
1.
Insert the lock into the cavity.
2.
Mark & drill faceplate holes. Fasten with faceplate screws to hold lock in
place.
3.
For locks with door detector, see 201082 installation guide to connect.
INSTALLING THE STRIKE
1.
Refer to template to determine strike location on jamb.
2.
Using strike as template, mark and chisel recess.
Drill screw holes and fasten.
ADJUST BEVEL
1.
Loosen adjustment screws at top and bottom of case.
2.
Turn front to desired bevel.
3.
Re-tighten adjustment screws.
NOTE:
Holes for the fixation of the SALTO electronic escutcheon are not included in this
template. Please use the template included in the escutcheon box.
LUBRICATION
All locks come lubricated from the factory with a lithium based grease. We recommend, however, continued periodic lubrication
of internal moving parts with a commercial quality grease. This can add years to the life of the lockset by reducing excessive
wear. For more severe environments, lubrication should be applied more frequently.
HANDING ANSI door code Required Information
www.saltosystems.com
Adjustment
screw
Pivot
lock front
Top of
Lock
Door code
Mortise code
LH
RHR
RH
LHR
L
R
All contents current at time of publication.
SALTO Systems S.L. reserves the right to change availability of any
item in this catalog, its design, construction, and/or materials.
Eng
L
C
L
C
L
C
-L
EV
ER
-M
A
N
ILL
A
-B
EQ
U
ILL
E
L
C
L
C
V
e
rt
ic
a
l c
e
n
te
r
lin
e
o
f B
a
c
k
se
t
(C
e
n
tro
v
e
rt
ic
a
l
d
e
la
e
n
tra
d
a
)
(C
e
n
tre
v
e
rt
ic
a
l
d
u
a
xe
)
V
e
rt
ic
a
l c
e
n
te
r
lin
e
o
f D
o
o
r
(C
e
n
tro
d
e
la
p
u
e
rt
a
)
(C
e
n
tre
v
e
rt
ic
a
l
d
e
l´
a
xe
)
Strike Lip Position
(Posición labio del cerradero)
(Position du recouvrement gâche)
1"
(2
5 m
m
) D
iam
ete
r
Tu
rn
p
ie
c
e
H
o
le
(in
sid
e
o
n
ly
)
D
rill
d
e
p
th
4-
1/
2"
(V
a
c
ia
d
o
p
ro
f.1
14
m
m
)
(P
ro
fo
n
d
e
u
r
u
sin
a
g
e
)
Bo
to
n
d
e
p
riv
a
c
id
a
d
(s
o
lo
p
o
r e
l in
te
rio
r)
C
EN
TE
RL
IN
E L
O
C
K
C
A
SE
C
EN
TR
O
D
E L
A
C
ER
RA
D
U
RA
C
EN
TR
D
EL
L
A
M
O
RT
IS
E
C
EN
TR
EL
IN
E O
F S
TR
IK
E
C
EN
TR
O
D
EL
C
ER
RA
D
ER
O
C
EN
TR
E D
E L
A
G
Â
C
H
E
Tro
u
p
o
u
r b
o
u
to
n
d
e
p
riv
a
c
ité
(s
e
u
l in
te
rie
u
r)
O
5/8" (1
6mm
)
3/8" (9,5 mm)
RH
LH
P-221378 - 1/4 -ED.10/11/2016
38,1
1-1/2" (
)
61,6
2-27/64" (
)
Remove special screw with allen wrench.
Pull latch bolt out of lock.
Rotate latch bolt 180º and reinstall into lock,
pushing the latch bolt into the lock and then releasing.
From oposite side, insert the special screw and
tighten securely with the allen wrench.
Make sure foot is
under latch surface
Cannot put in lock with
foot above latch surface
LATCHBOLT POSITION CHANGING
O
1" (2
5,4m
m)
3/3
2" o
r
Tor
x 1
0
Hand changing
Changement de main
Cambio de mano
F
E
Eng
1
2
3
4
HE
IG
HT
A
BO
VE
F
LO
O
R
OF
LEVER
OF
DOOR
EDGE
L
C
L
C
L
C
L
C
OF
LEVER
OF
BASKSET
