![background image](http://html.mh-extra.com/html/safe-fleet/700-1110-r5/700-1110-r5_installation-manual_798334001.webp)
© 2021 Safe Fleet | All rights reserved. Part #700-1110 R5
2021 Safe Fleet | All rights reserved. Part #700-1110 R5
Power On and Test
1.
Turn on accessory power to the vehicle.
2.
Put the vehicle in reverse gear.
During normal operation, the monitor only turns on
when the vehicle is shifted into reverse.
If the monitor fails to turn on when power is applied,
confirm power connections. Disconnect and firmly
reconnect the LCD Monitor cables.
3.
For installations with video recorder integration,
configure the recorder as shown in the RVS
Recorder
Configuration Guide
(700-1103).
4.
Adjust the camera view so that the bumper of the vehicle
is just visible across the bottom edge of the monitor, as
shown.
5.
Refer to the camera installation guide for details on
closing and fastening the camera once it has been aimed.
6.
Turn off accessory power to the vehicle.
LCD Monitor Configuration
For information on custom monitor settings, see the
Rear
Vision Monitor Quick Install Guide
(700-1107)
Related Documents
For full product details, and access to our Document Library,
please visit the Seon Community Web site:
If you do not have access credentials, please contact
Customer Service.
Customer Service
•
Service:
1.844.899.7366
•
General Enquiries: 1.877.630.7366
•
If your RVS device is to be returned, please contact
Customer Service, and provide the model and/or serial
number of your unit. Ask for a Return Merchandise
Authorization (RMA) number. An RMA number allows the
Service Technicians to better track your product when it
comes in for service. Please show the RMA number on the
outside of the package. ANY RETURNED PRODUCT
WITHOUT AN RMA NUMBER MAY BE REFUSED.
Warranty
For full warranty information, please visit:
http://www.seon.com/documents/Seon-Warranty.pdf
Rear Vision System Installation Guide
for Standalone and Video Recorder Integration
Introduction
The
Rear Vision System
(
RVS
) for vehicles enables the driver to see the camera output on a dash-mount monitor
whenever the reverse signal is triggered. The video feed can be mirrored with monitor settings.
This document covers physical installation of RVS hardware components. The RVS can be installed in two ways:
•
Standalone
: the RVS is powered from the vehicle, and displays on the dashboard monitor without passing
through the recorder;
RVS video is NOT recorded
.
•
Recorder Integration
: Using a recorder camera socket, RVS camera video runs through the video recorder
before appearing on the monitor.
RVS video, events, and alarms are recorded.
For details on setting up a
recorder for RVS integration, see the RVS
Recorder Configuration Guide
(700-1103).
Note
: High definition camera views cannot be displayed on the monitor.
When installed, RVS typically operates as follows:
•
The monitor is usually OFF (dark)
The monitor only turns ON when the vehicle is put into reverse gear (REVERSE signal is applied)
Important
:
When the vehicle ignition is turned on, the recorder may require approximately one minute to boot
up before video from the rear view camera appears on the dashboard monitor
.
System Installation Components
Rear view camera with corresponding mounting hardware.
Option A
: HExHD or HEHDxx camera harness
Option B
: 75’ Camera extension cable (060-1094)
Camera cable adaptor for retrofit (060-1095)
7” Monitor (080-1059), including sunshade (665-1020),
bracket (660-1073), and hardware kit (020-1042)
Rear Vision Monitor Quick Install Guide (700-1107)
20’ Video extension cable (HEHD20)
*
Monitor power and connector harness (060-1096)
RCA cable adaptor (060-1102)
Expansion harness for TH4/DH4/TH6/TH8/NH16 HX/NX
(060-1059)
*
Expansion harness for TL-HD (060-1014)
*
Monitor diode kit (020-1045)
*
Components not required for standalone installations