EZ Temp Digital Thermometer
Model # A00AA3814
Battery Requirements:
This product requires 2 AAA standard alkaline batteries. Locate the battery cover on the rear of the thermometer and gently slide
the cover down to remove it. Insert 2 AAA alkaline batteries and be sure to observe the correct polarity. Replace the battery cover. We do NOT recommend
the use of heavy duty or rechargeable batteries.
Auto Off:
To conserve battery power, this product will automatically turn off in 5-6 minutes if temperature is lower than 122°F (50°C) with no obvious
temperature change, or no button activity.
A00AA3814 • 80023105 • 03.19.15
Notes:
a.
Clean the probe with a damp cloth before each use.
b.
Do not submerse the unit in water or place in dishwasher. Clean it with a damp cloth only.
c.
Do not insert the probe into any environment where the temperature is above 572°F (300°C). It may cause damages if it is being used at a
temperature that is higher than 572°F (300°C). Please remove the unit from the cooking environment if there is a high temperature alarm.
d.
Do not place the unit in oven, microwave, etc. Otherwise, it may cause damage to the product. Please do not place the unit in an environment that
is over 572°F (300°C).
e.
Allow the unit to cool down, then clean and dry the probe before folding it back into the handle.
f.
Avoid dropping the unit as it could affect the accuracy and function of unit.
g.
The normal operation of the product may be disturbed by strong electromagnetic interference. If so, simply reset the product to resume normal
operation by removing and re-installing the batteries.
Instructions:
Languages selection
(English is the default language):
Press and hold the “SET” button while installing batteries. There are a total of 7 language-choices. Select the language:
Press + or – button to select the desired language. If the selected language is EN, the language order is EN, DE, FR, IT,
ES, SW, and DU. If the selected language is DE, the language order is DE, FR, IT, ES, SW, DU, and EN. To confirm and
escape the language-selecting mode: Press “SET” button to confirm the selected language and exit.
°C/°F selection:
Slide the °C/°F switch to select the desired display unit. The selector switch is located inside the battery compartment.
Power On
: Press and hold “
SET
“ button about 1 second to power on the unit. After powering on, the unit will display the measured
temperature; the food type and the corresponding recommended cooking temperature (just before last turned off), and the
unit is in normal mode. Please refer to the figure 1, right.
Power Off
: Turn off manually: Press and hold the “
SET
” button for 3 seconds.
Battery replacement indication:
Please replace the batteries when the low battery icon ( ) displays on the LCD. Batteries: 2 AAA.
Meat type:
In the normal mode, press “-“ or “+” button to select the meat type (Please refer to the table below for the meat types). The
USER setting allows a custom temperature to be programmed for any temperature between 32°F (0°C) to 392°F (200°C) .
Figure 1
Sequence
Item
English (EN) German (DE) French (FR) Italian (IT) Spanish (ES) Swedish (SW) Dutch (DU)
Med Rare 63C/145F
Fresh Beef BEEF
RIND
BOEUF
MANZO
VACA
NOETK
RUNDV
Med
71C/160F
Well Done 77C/170F
Med Rare 63C/145F
Fresh Veal VEAL
KALB
VEAU
VITEL
TERNR
KALVK
KALF
Med
71C/160F
Well Done 77C/170F
Med Rare 63C/145F
Fresh Lamb LAMB
LAMM
AGNEA
AGNEL
CORDR
LAMM
LAM
Med
71C/160F
Well Done 77C/170F
71C/160F
Pork
PORK
SCHWN
PORC
MAIAL
CERDO
GRISK
VARKE
74C/165F
Poultry
POULT
HUHN
POULT
POLLO
POLLO
KYKLI
KIP
74C/165F
Turkey
TURKE
TRUTH
DINDO
TACCH
PAVO
KALKO
KALKO
71C/160F
Burger
BURGR
BURGR
BURGR
BURGR
BURGR
BURGR
BURGR
71C/160F
User
USER
ANWEN
USAGR
UTENT
USUAR
FORBR
GEBRU
Printed In China
Instruction Manual © 2014 • Saber Grills, LLC.
Doneness levels:
In the beef, veal, and lamb options, there are 3 doneness levels (Med. Rare /Medium /Well Done) available (Please refer to the table below for
temperature levels of different doneness levels).
USER defined alarm temperature setting:
To enter the USER mode, press the ”SET” button in USER option (alarm temperature blinks). The alarm temperature can be set by pressing “-“
or “+” button to the desired setting. After setting the alarm temperature, press the “SET” button again to confirm and exit. The “alarm temperature”
on LCD will now stop blinking.
Alarm:
Once the detected temperature reaches the set alarm temperature, there are four 4-beep audible alerts. The symbol shows on the
LCD. If the detected temperature still stays above the alarm temperature, the unit will alert every 30 seconds.
High temperature alert:
The unit
will alarm and the LCD flashes with “
HHH
” if detected temperature is higher than 392°F (200°C)
Warranty:
One year limited warranty.
