background image

Congratulations and thank you for the purchase of your Rubbermaid 7' x 7' storage building. Before you begin assembly please 
be sure to check your local building codes, ordinances and restrictions, and applicable neighborhood governances.  

BEFORE YOU BEGIN – SURFACE PREPARATION 

To ensure proper assembly and performance your shed needs to be built on a solid, level surface. A cement or patio surface, or 
a treated-wood platform is recommended.

BEFORE YOU BEGIN – LOCATION

When choosing a location in your yard make sure you choose an area with easy access and one that provides proper drainage 
for water to run away from the shed location.  

Prior to beginning the assembly please complete the following items: 
• Thoroughly review all assembly steps (it is important that the steps are followed in the correct order).
• Review the parts list and make sure that no parts are missing.

IMPORTANT – DO NOT  
RETURN TO THE STORE

  

For assistance with your 
Rubbermaid

®

 Storage Building

or for additional product 
information call our toll-free 
Consumer Service number:  
1-888-895-2110
M–F 8:30AM to 5:00PM EST
or visit us online at:
www.rubbermaid.com.

5H80

94¼"

84"

85½"

1821375

Summary of Contents for 5H80















Reviews: