HOW TO OPERATE THE LED FLASHLIGHT
Press the POWER BUTTON for three [3] seconds to turn ON the LED flashlight.
Once the LED light is turned ON, lightly pressing the POWER BUTTON will cycle through additional
modes (illumination, strobe, SOS).
CHARGING A CELL PHONE OR TABLET
1. Plug the USB adapter into the USB output port of the RP Power Bank.
2. Connect the appropriate adapter to your cell phone or tablet.
3. Press the POWER BUTTON to start charging the electronic device. The indicator lights will be on
when the RP Power Bank is charging.
POWER SUPPLY FOR 19V NOTEBOOK
(optional)
1. Plug the Switch Cable into the 19V/3.5A output port of the RP Power Bank.
2. Connect the appropriate adapter for your notebook for the Switch Cable, and plug it into your
notebook.
3. Press the POWER BUTTON to supply power to your 19V notebook.
HOW TO CHARGE THE RP POWER BANK
1. Plug the AC Switching Wall adapter into an electrical outlet using the correct electrical adapter.
2. Connect the other end of the AC adapter to the 14V/1A input port of the RP Power Bank.
OR
1. Plug the DC adapter into the socket of a vehicle's cigarette lighter or DC outlet.
2. Connect the other end of the DC adapter to the 14V/1A input port of the RP Power Bank.
BATTERY CAPACITY LED INDICATOR
Press the POWER BUTTON to check the remaining battery capacity.
INDICATOR LIGHTS
1 Flash
1 Solid
2 Solid
3 Solid
4 Solid
BATTERY CAPACITY
5%
25%
50%
75%
100%
The indicator lights will flash one by one while charging. Different numbers of solid indicator lights
display the different storage levels of the RP Power Bank. All indicators light up when charging is
paused or completed.
JUMP START A 12V VEHICLE BATTERY
1. Make sure the battery capacity of the RP Power Bank is not less than 75%. (At least three [3]
indicator lights stay ON.)
2. Connect the jump start cable to the 12V jump start socket of the RP Power Bank.
3. Connect the jump start cable clamps to the drained battery of the vehicle. Connect the RED clamp
to the positive (
+
) terminal and the BLACK clamp to the negative (
−
) terminal.
4. Start the vehicle.
5. When the vehicle has started, remove the jumper cable within
30 SECONDS
from the RP Power
Bank and disconnect the RED and BLACK clamps from the vehicle battery.
6. Leave the vehicle's engine running.
WATERPROOF RATING
IP65: Dust-tight and protected from moisture challenges up to jetting water.
SPECIFICATIONS
Battery Capacity: 18,000 mAh
Charging Time: Approximately 6 hours
Battery Life Cycles: >1000
Start Current: 350A
Weight:
28.4 oz (805g) Peak Current: 700A
Input:
14V/1A
Operation Temp: -4°F~120°F (-20°C~60°C)
Outputs:
5V/2.1A; 19V/3.5A; 12V Jump Start
Dimensions:
210 x 96 x 33mm (8.27 x 3.78 x 1.30 in)
TROUBLE SHOOTING
STATUS
Green LED
Red LED
BEEPING
Detecting
Flashing
Flashing
NO
Ready to Start
Solid
OFF
NO
Low Voltage
OFF
Solid
NO
High Voltage
OFF
Solid
NO
Short-Circuit
Flashing
Flashing
YES
Reverse Polarity
Flashing
Flashing
YES
Reverse Charge/Current
Solid
Solid
YES
Overheat
OFF
Flashing
YES
No operation in 30 seconds after
jumper clamps are connected to
battery terminals
OFF
Solid
NO
TOXIC AND HARMFUL SUBSTANCES
Composition and Amount of Toxic and Harmful Substances in the RP Power Bank
Pb
Hg
Cd
Cr (VI)
PBB
PBDE
: Indicates all homogeneous materials’ hazardous substances content are below the
MCV limit specified in the Standard 2002/95/EC (RoHs).
SMART CABLE
Functions:
Instructions:
1. Plug the blue EC5 connector of the Smart Cable into RP Power Bank 12V jump start socket.
2. Connect the Smart Cable to the vehicles' battery terminals; positive (+) to positive (+),
negative (–) to negative (–).
3. If the RP Power Bank is ready the "Start" indicator lights up GREEN.
4. Start the vehicle.
5. The time relay of the Smart Cable is 30 seconds. The RP Power Bank shuts down automatically,
without any operation in 30 seconds. Remove the Smart Cable from the RP Power Bank to
reset the Smart Cable.
6. Connecting the battery terminals incorrectly, a short-circuit, and low voltage will trigger the
Smart Cable alarm and turn the indicator lights to RED.
7. ONCE THE VEHICLE HAS STARTED, REMOVE THE SMART CABLE FROM THE BATTERY
TERMINALS IN
30 SECONDS
.
1. Low voltage protection.
2. Reverse polarity protection with alarm.
3. Short-circuit protection.
4. Overload protection.
5. Overcharge and discharge
protection
Short-Circuit Protection
Overcharge Protection
Discharge Protection
PROTECTION
19V/3.5A Connectors
19V/3.5A
Switch Cable
(optional)
PRODUCT LAYOUT
ACCESSORIES
ON/OFF Button
LED Light
12V Jump Start Socket
19V/3.5A Output Port
USB Output
14V/1A Input Port
USB Charging
Adapter Cable
NOTE:
Actual product and accessories may vary slightly from the pictures shown above.
Micro-B USB
Apple Lightning
AC Switching Wall Adapter
DC Adapter
Smart Cable
with Clamps
Battery Indicating Lights [4]
