Roberts Gorden VANTAGE NP CTHN-100 Installation & Operation Manual Download

Page: 1 / 48

Roberts-Gordon, LLC

1250 William Street
P.O. Box 44
Buffalo, New York 14240-0044
Telephone: 716.852.4400
Fax: 716.852.0854
Toll Free: 800.828.7450

www.rg-inc.com

Quality in Any Language™

CTHN-40
CTHN-60
CTHN-80

CTHN-100

CTHN-125
CTHN-150
CTHN-175

CTHN-200

P/N 152101NA Rev A 10/06

Vantage

Negative Pressure

Unitary or Multiburner

Infrared Heater

Installation,

Operation &

Service Manual

WARNING

FOR YOUR SAFETY

If you smell gas:

1. Open windows.

2. DO NOT try to light any appliance.

3. DO NOT use electrical switches.

4. DO NOT use any telephone in

your building.

5. Leave the building.

6. Immediately call your local gas

supplier after leaving the building.

Follow the gas suppliers

instructions.

7. If you cannot reach your gas

supplier, call the Fire Department.

Fire Hazard

Do not store or use gasoline or other

flammable vapors and liquids in the

vicinity of this or any other appliance.

Some objects will catch fire or explode

when placed close to heater.

Failure to follow these instructions can

result in death, injury or property

damage.

WARNING

Installation must be done by a contractor qualified

in the installation and service of gas-fired heating

equipment or your gas supplier.

Improper installation, adjustment, alteration, service

or maintenance can result in death, injury or property

damage. Read the Installation, Operation and Service

Manual thoroughly before installing or servicing

this equipment.

Installer

Please take the time to read and understand

these instructions prior to any installation.

Installer must give a copy of this manual to the owner.

Owner

Keep this manual in a safe place in order to provide

your serviceman with necessary information.

Summary of Contents for VANTAGE NP CTHN-100

















































Search results

Summary of Contents for VANTAGE NP CTHN-100

Reviews:

Related manuals for VANTAGE NP CTHN-100

Brands by name

Popular brands

Roberts Gorden VANTAGE NP CTHN-100, Installation & Operation Manual

Search results

Summary of Contents for VANTAGE NP CTHN-100

Reviews:

Related manuals for VANTAGE NP CTHN-100

Brands by name

Popular brands