Rinnai Composite Recess Box Installation Manual Download | Manualshive

Page: 1 / 12

background image

Composite Recess Box (R1406)

Installation guide

These instructions are a guide only, designed to be used in conjunction with the
NZ Building Code Approved Document - External Moisture E2. The recess box
installation can be compared to the detail required to install a meter box.

Territorial authorities may have their own additional requirements regarding
this type of installation. If in any doubt over compliance with building codes, it is
advisable they are consulted prior to installation.

1
2
3
...
»

Summary of Contents for Composite Recess Box













Reviews:

No comments

Related manuals for Composite Recess Box

Brand: Conteg Pages: 40

Brand: StarTech.com Pages: 11

Brand: Manhattan Pages: 19

DATEC-CONTROL M

Brand: OKW Pages: 16

Brand: Bartec Pages: 4

Brand: Icy Box Pages: 5

ProLiant BL490c - G6 Server

Brand: HP Pages: 101

Brand: HP Pages: 51

ProLiant BL280c G6

Brand: HP Pages: 112

Brand: HP Pages: 25

Brand: HP Pages: 4

DL320s - ProLiant 9TB SATA Storage Server NAS

Brand: HP Pages: 150

D6000 Disk Enclosure

Brand: HP Pages: 54

ProLiant BL495c - G5 Server

Brand: HP Pages: 3

Brand: MikroTik Pages: 2

Brand: DeLOCK Pages: 16

Brand: Minebea Intec Pages: 24

Brand: InWin Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands