background image

CUSTOMER SERVICE

If you are missing parts or have any questions about this product, contact us first. You can also order parts by writing to the

address above. Include the product model number, color, and a brief description of the part. Call 1-800-762-1751.

CARE AND CLEANING

DO NOT scratch or chip the finish. DO NOT use abrasive chemicals for cleaning. Dust often using a clean, soft, dry cloth.

Blot spills immediately and wipe with a clean damp cloth. If the crib is to be stored, store in a cool dry place and carefully

package all original hardware to protect from loss.

TOOLS AND INSTALLATION

Tools Necessary: Allen Key (included)

NOTE

: It may be easier to assemble product with two people.

NOTE

: When inserting bolts, turn clockwise until tight. Then loosen 

1

2

 - 

3

4

  of a turn. After crib is

completely assembled, return to each bolt and tighten. Use wax or soap on all bolts to facilitate assembly

Made in Vietnam

Distributed in the U.S.A. by:

Restoration Hardware Baby & Child

11640 Harrel St. Suite B

Mira Loma, CA 91752

www.rhbabyandchild.com

Distributed in Canada by:

Restoration Hardware Canada, Inc.

1500-1055 West Georgia Street

Vancouver, British Columbia V6E4N7

WARNING:

 Read all

instructions before assembling this

product. 

KEEP INSTRUCTIONS

FOR FUTURE USE.

Page  1  of  10

Summary of Contents for MARCELLE











Reviews: