background image

ELECTRIC CHAIN SAW

SECTION

PAGE

Symbol Information ............................................................ 2
Safety Warnings ................................................................. 3

Before Operating Chain Saw ....................................... 3
Kickback ...................................................................... 3
Pushback and Pull-in ................................................... 4
Chain Saw Operation .................................................. 4
Maintenance and Storage of Chain Saw ..................... 4

Product Identification ......................................................... 5
Chain Saw Names and Terms ............................................. 5
Unpacking ........................................................................... 6
Assembly ............................................................................ 6
Saw Chain Tension Adjustment ......................................... 7
Filling Oil Tank .................................................................. 7
Operating Chain Saw .......................................................... 8

Extension Cords .......................................................... 8
Oiling Chain ................................................................ 8

SECTION

PAGE

Cutting With the Chain Saw ........................................ 8
Chain Brake ................................................................. 8
Trimming a Tree .......................................................... 9
Felling a Tree .............................................................. 9
Limbing a Tree ............................................................ 10
Bucking a Log ............................................................. 11

Cleaning and Maintenance ................................................. 12

Cleaning Saw Body ..................................................... 12
Care of Guide Bar ....................................................... 12
Sharpening Your Saw Chain ....................................... 12

Recycling ........................................................................... 14
Storage ............................................................................... 14
Replacement Parts .............................................................. 14
Troubleshooting .................................................................. 15
Warranty Information ......................................... Back Cover

®

EL-4

MODEL

TYPE

100271-01

230V

~

50Hz

1450W

1995

®

®

OWNER’S MANUAL

IMPORTANT

Read and understand this manual before assembling or operating this chain saw.
Improper use of saw can cause severe injury. Keep this manual for future reference.

CONTENTS

Summary of Contents for 100271-01

















Reviews: