background image

TonerRefillKits.com 

 

RechargX™ RX022

Mon - Fri  8am - 5pm ET                     © 1995-2011 ReChargX™, EmptyX, TonerRefillKits and TonerRefillKits.com, the TonerRefillKits logo, the  

2011.05.20

800.527.3712 or 352.343.7533                 ReChargX™ and EmptyX logos are trademarks owned by TonerRefillkits, LLC. All rights reserved. 

Page 1 of 7

The Canon E16/E20/E32/E40 are the toner car-

tridges most frequently found in the Canon PC 

140, 210, 230, 300, 430, 530, 710, 730, 740 

and others, as shown in figure 1.

These  toner  cartridges  are  quite  easy  to  refill 

using  our  ReChargX™  RX022  Premium  Print 

Toner Refill Kit.

Within these ReChargX™ RX022 Premium Print 

Toner Refill Kit instructions, we will be adding 

new toner and removing the waste toner.

Step 1: Orient the Toner Cartridge

Orient  the  cartridge  handle  to  the  right  side, 

opposite from the side of the cartridge with the 

engraved arrow.

In this orientation the text on the cartridge will 

be right side up, as shown in figure 2.

The white circle indicates where we will be 

placing  the  toner  hopper  hole;  explained 

further in step 2.

Step 2: Determining the Toner Hopper 

Hole Location

With the cartridge in the same orientation as 

shown  in  figure  2,  we  will  create  the  toner 

hopper hole on the left of the cartridge on the 

small indent, shown by the white circle (fig 3).

These  four  cartridges,  while  they  contain 

different amounts of toner when they leave 

the Canon factory, actually all have the same 

capacity within the toner hopper.

The amount of toner provided in the ReChargX™ 

RX022 Toner Refill Kit will give you the amount 

equal to the Canon E40 high-yield toner cartridge, 

no matter which type of cartridge you start with.

ReChargX™ RX022 Instructions

For use in the Canon E16, E20, E32, E40 toner cartridges

Figure 1

: Canon E16/E20/E32/E40 toner cartridge

Figure 2

: Cartridge oriented with the cartridge handle   

 

    toward your right side

Figure 3

: The toner hopper hole location

Summary of Contents for RX022








Reviews: