background image

www.radialeng.com

Radial Engineering

1638 Kebet Way,  Port Coquitlam   BC   V3C 5W9      

Tel: 604-942-1001   Fax:  604-942-1010  

email: [email protected]

Pro48 Active Direct Box 

Users Guide

True to the Music

Radial Engineering is a division of C•TEC (JP CableTek Electronics Ltd.)

Radial Pro48 users guide - v1.0 -  Part #: R870 1135 00

Subject to change without notice

Pro48 User Guide

Radial Engineering

RADIAL LIMITED THREE YEAR 

TRANSFERABLE WARRANTY 

Radial Engineering - a division of JP Cabletek Electronics Ltd.- warrants this product 

to be free from defects in material and workmanship and will remedy any such defects 

free of charge according to the terms of this warranty. Radial Engineering will repair 

or replace at its option any defective component(s) of this product, excluding the 

finish, the footswitch (footswitch is warranted for 90 days) and wear and tear from 

normal use, for a period of three (3) years from the original date of purchase. In the 

event that a particular product is no longer available, Radial Engineering reserves 

the right to replace the product with a similar product of equal or greater value. To 

make a request or claim under this limited warranty, the product must be returned 

prepaid in the original shipping container (or equivalent) to Radial Engineering or 

to an authorized repair centre and you must assume the risk of loss or damage. A 

copy of the original invoice showing date of purchase and the dealer name must 

accompany any request for work to be performed under this limited warranty. This 

limited warranty shall not apply if the product has been damaged due to abuse, 

misuse, misapplication, accident or as a result of service or modification by any 

other than an authorized repair centre.

THERE ARE NO EXPRESSED WARRANTIES OTHER THAN THOSE ON THE 

FACE  HEREOF AND  DESCRIBED ABOVE.  NO  WARRANTIES,  WHETHER 

EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO, ANY IMPLIED 

WARRANTIES  OF  MERCHANTABILITY  OR  FITNESS  FOR A  PARTICULAR 

PURPOSE, SHALL EXTEND BEYOND THE RESPECTIVE WARRANTY PERIOD 

DESCRIBED ABOVE OF THREE YEARS.

RADIAL ENGINEERING SHALL NOT BE RESPONSIBLE OR LIABLE FOR ANY 

SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LOSS ARISING 

FROM THE USE OF THIS PRODUCT. THIS WARRANTY GIVES YOU SPECIFIC 

LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS, WHICH MAY VARY 

DEPENDING ON WHERE YOU LIVE.

Pro48 User Guide

Radial Engineering

Pro48 SPECIFICATIONS

Frequency response:  

 

20Hz to 40kHz 

Linear performance: 

 

+/- 0.12dB 20Hz to 20kHz

Total harmonic distortion:    

0.01 % from 20Hz to 20kHz

Input impedance:  

 

220K ohms

Balanced outputs:  

 

600 ohms, mic level, pin-2 hot 

PAD: 

 

 

-15dB

Power: 

 

 

48V Phantom

FEATURES AND FUNCTIONS

INPUT  -

  jack  connects  to  instruments 

like guitars and keyboards.

-15dB  PAD

  -  reduces  the  input  level 

by 15dB to prevent overload from high 

output  devices  like  CD  players  and 

active pickups.

LED  INDICATOR  -

  lights  to  confirm 

phantom power is active and the Pro48 

is working.

THRU  -

  jack  passes  the  instrument 

signal to the on-stage amplifier.

FULL  BOTTOM  FOOT  -

  neoprene 

foam  foot  provides  electrical  isolation 

and plenty of friction to stay put.

14  GAUGE  STEEL  -

  bookend  shell 

creates  a  protective  zone  around  the 

switches and connectors.

OUTPUT  -

  600

  balanced  mic-level 

output (pin-2 hot) drives long cables for 

runs  to  1000  feet  without  appreciable 

loss.

GROUND LIFT -

 helps to reduce hum 

and buzz caused by ground loops.

SWITCHING POWER SUPPLY -

 steps 

up the current from phantom power to 

produce 9 volt internal rails. With more 

voltage to work with than typical active 

DIs, the Pro48 exhibits more headroom 

and  dynamic  range  while  lowering 

noise.  

MILITARY-GRADE -

 double-sided PCB 

is bolted to steel standoffs for road-tough 

construction.

ISOLATED CONNECTORS -

 are 100% 

electrically isolated from the chassis.

ACTIVE DRIVE CIRCUIT - 

electronically 

balances  the  signal  and  converts  it  to 

low-Z mic-level.

I-BEAM DESIGN -

 inner steel enclosure 

is made extremely rigid with an I-beam 

profile. This eliminates stress that could 

torque the PC board and cause solder 

joint failure.

1

2

3

4

1

2

3

5

4

5

7

8

9

10

6

11

6

7

8

12

13

10

9

11

12

13

True to the Music

Reviews: