![background image](http://html1.mh-extra.com/html/r-u-ready/speed-timer-3000/speed-timer-3000_operating-instructions_3092169001.webp)
Speed-Timer 3000 and 3000 (RF) Operating Instructions.
Speed-Timer 3000 and 3000 (RF): Install a 9 volt Alkaline Battery in the battery
compartment of the Speed-Timer 3000 and 3000 (RF)
Range Officer Mode: (instant start signal)
Press and hold down the START/RESET key for three seconds or longer (“0 sec” will appear
on the screen) then release the START/RESET key to initiate the Record Mode for an instant
start. Then read the number of shots fired, the elapsed time, and the split time between the last
two shots fired
Shot Time: Practice Mode (2.5 to 5.0 second Random Delay Start Signal) Press
and hold down the START/RESET key from one to three seconds (“dEL” will appear on the
screen) then release the START/RESET key to initiate the Record Mode with 2.5 to 5.0
second Random delay start. Wait for the audible start signal and begin shooting. Then read
the number of shots fired, the elapsed time, and the split time between the last two shots fired.
Review Mode:
To review all shots fired (in order), press and release (less than one second) the
START/RESET key and start cycling through the shots fired. Press and release (less than one
second) for all remaining shots.
Last 8 Shot Stings
Enter the Review Mode above, push the up or down arrow to review the last shot fired in the
last 8 Strings. Push the START/RESET Key one time to exit Last 8 Shot Strings and return to
the Review Mode and display all shots fired in the unsaved string.
NOTE the strings do not get saved in memory, unless you have started a new string. The
current string will still be on the screen with all shots fired and the last eight starts will be
stored in memory.
Turning the Timer Off
Enter the Review Mode as above and the Timer will automatically shut off in approximately ten
minutes in the Review Mode or while in the Review Mode you may press the MODE key to
shut the timer off. You will not lose the shot times in memory. Press and release the
START/RESET key at any time for less than one second to reactivate. Removing or changing
the battery will not erase shot times stored.
Range Officer Walk Through , PAR, Sensitivity Setting or Battery Test: Setting “r0F” Time ,“P”
Time, Sensitivity Setting “Pot” and Battery Test “bAt”
While in Shot Time, the MODE key is deactivated preventing any accidental interruption in
recording shots fired. The Setting “r0F” Time ,“P” Time, Sensitivity Setting “Pot” and Battery
Test “bAt” “can only be activated by pressing and releasing the MODE key two times from the
Review Mode or if the timer is off, one time from a blank screen.
Press and release the MODE key for 3 to 4 seconds to toggle to “r0F” Time ,“P” Time,
Sensitivity Setting “Pot” and Battery Test “bAt” .
Stop at the program required.
RO Officer Walk Through; Choice a walk through time In “r0F”, move the clock in full minutes
from 1-10 minutes, by using the up or down arrow keys to set the desired time. (this time will
remain in memory until it is changed using the above method) Push and release the
“START/RESET ” to start the walk through timing. Note: a single signal will sound to start the
count down, a double signal will sound to warn of one minute remaining in the walk through
and three signals to warn that the walk through time has expired. The Timer will then enter
Record Mode automatically at the end of the set time or if for any reason you stop the clock.
PAR Time: Setting PAR Time In “P” Mode (see above). The screen will display OFF or a time
previous set. Using the up arrow key move the clock to the desired time.(holding down a arrow
key will cause the time to cycle at a faster rate) Press the START/RESET key to exit PAR
setting and save your selection. The PAR time is set and may be operated in either random
delay start or instant start with full review capabilities. Note: The letter P will be present to
indicate PAR time is active and set when starting the Timer in Shot Time. PAR range .1 second
to 10 Minutes (600 seconds) in 10 th of a second. Pushing and holding in the UP or Down key
will allow the time to rapidly advance. At the end of the set PAR time the buzzer will sound and
show the last shot fired and number of shots fired before the buzzer, review your shots by
using the up and down arrows. Any shot fired after the during or after the buzzer is considered
overtime and does not display.
To exit PAR time and return to Shot Time.
From the Review Mode, press and release the MODE key to exit and press and release the
MODE Key for 3 Seconds to enter setup. Toggle to “PAR” Time, arrow down until the screen
reads OFF. Press the START/RESET key to exit.
To exit RO Officer Walk Through: Toggle through by pressing the MODE Key the “r0F”
Time ,“P” Time, Sensitivity Setting “Pot” and Battery Test “bAt” to “P” Time. Press the “MODE”
key to exit and turn the Speed-timer 3000 off.
Sensitivity
The Speed-Timer 3000 is factory set for a sensitivity to handle the majority of Firearms indoors
and out. It is set to pickup shots from approximately 20 Feet (6 Meters) from the Timer. Under
normal circumstances there is no need to change these setting, however this Timer can be
modified to suit a particular location or application if necessary.
Sensitivity Adjustment
While in Shot Time, the MODE key is deactivated preventing any accidental interruption in
recording shots fired. The Setting “r0F” Time ,“P” Time, Sensitivity Setting “Pot” and Battery Test
“bAt” “can only be activated by pressing and releasing the MODE key two times from the Review
Mode or if the timer is off, by pressing and releasing the MODE key one time from a blank screen.
With the Screen blank, press, hold and release the MODE key for 3-4 Seconds and release and
toggle to Setting “r0F” Time ,“P” Time, Sensitivity Setting “Pot” and Battery Test “bAt” setup
screens. Stop at Sensitivity Setting “Pot”.
To change the sensitivity setting use the up or down arrow to choice between 0 and 63 as a
setting to suit your application. Test the setting by firing a few rounds so the you can test your
setting, you will note that as you fire the number in the right corner of the screen will increase to
indicate that the shots have been tested. There is no need to go to Shot Time Mode for this
adjustment.
When you are satisfied with the results, simply us the arrow keeps to exit the
setup program.
Factory Setting is 32.
Battery Test
While in Shot Time, the MODE key is deactivated preventing any accidental
interruption in recording shots fired. The Setting “r0F” Time ,“P” Time, Sensitivity Setting “Pot” and
Battery Test “bAt” “can only be activated by pressing and releasing the MODE key two times from
the Review Mode or if the timer is off, one time from a blank screen.
Simply index through r0F” Time ,“P” Time, Sensitivity Setting “Pot” to Battery Test “bAt, and read
the current health of your battery. Example 9.0 volts. Press the Mode to Exit.
Battery Low Indicator : Should the word “Time” on the Timer Screen start to flash slowly, this is
also a indication that the battery has reached a low value and should be changed soon.
To Use the Hands Free Carry Case (Sold Separately) which Can protect your Speed-Timer 3000
when not in use. Will attach to your Belt for secure and easy access while recording shots. Just
fold the flap back, attach the flap to the Velcro and slip it on your belt, or can be attached to your
wrist, for "Hands Free" use while recording shots. Fold the flap around your wrist and attach to the
Velcro for "Hands Free" use.
DISPLAY with a Speed-Timer 3000 (RF) Only:
Install a 9 volt Alkaline Battery in the battery compartment of the DISPLAY.
Note: If you purchased your Speed-Timer RF Timer and Display together the following may not be
necessary as the ID would have been Factory Set, Factory Setting is 0000 RF Off
Turn on the DISPLAY with the on/off switch located on the left side of the unit. Make a note of the
ID displayed, on the screen, which will appear for approximately 5 Seconds.
With the screen on the Speed-Timer 3000 (RF) blank, hold down the MODE key on the Speed-
Timer 3000 (RF) for 7-10 seconds. When you the letters ID release the key.
You will now see a four digit ID displayed on the Speed-Timer 3000 (RF) with the first digit
flashing. Using the up and down arrow keys set the first number if required to the first number that
the DISPLAY displayed when it was first turned on and press the MODE key. The second digit will
now be flashing, again using the arrow key up or down to set this digit and press the MODE key.
Repeat this process for all remaining digits and press the MODE key to finish.
Your timer is now set to communicate with this DISPLAY only! This setting will not change unless
you repeat the above process.
Operating The Speed-Timer 3000 (RF) / DISPLAY
Make sure that your Speed-Timer 3000 (RF) is set to communicate with the DISPLAY as above.
Begin recording shots with your Speed-Timer 3000 (RF) and watch the DISPLAY display your
times, Shots Fired, Walk Through Count Down etc.
When not in use, turn off the DISPLAY using the switch on the left side of the unit to conserve the
battery life.
Always record the official time for any event as that
time displayed on the Speed-Timer 3000.
March 31 2017