background image

quest

quest

DRY 150

Quest PowerDry 1300

Installation, Operation and Maintenance Instructions

Installation, Operation and Maintenance Instructions

– Read and Save These Instructions –

This manual is provided to acquaint you with 
the dehumidifier so that installation, operation 
and maintenance can proceed successfully. 
Ultimate satisfaction depends on the quality 
of installation and a thorough understanding 
of this equipment. The dehumidifier is built 
around tested engineering principles and has 
passed a thorough inspection for quality of 
workmanship and function.

4201 Lien Rd 

Phone 608-237-8400

Madison, WI 53704 

Toll-Free 1-866-933-7476

www.QuestOnTheJob.com [email protected] 

– Read and Save These Instructions –

Specifications subject to change without notice.

TS-717

02/15

1

Quest PowerDry 1300

:

•  Roto-mold design
•  8 Gallons per day at 80ºF/60%RH (AHAM)
•  5.0 amps of power
•  12-inch recessed wheels
•  Rotating handle
•  Solid state control panel
• Lightweight
•  Lighted cord
•  Condensate Pump

Water Removal Rate (Gallons/Day) 

 

8 Gallons  

80˚F, 60% 

16 Gallons  90°F, 90%

quest

quest

Patent  8,938,981

Summary of Contents for PowerDry 1300














Reviews: