background image

INTRODUCTION 

This manual is designed to help you quickly and easily learn to use your Quantum Composers 
Model 9412/9412A pulse generator.  Rather than the usual array of knobs and switches, the 
9412/9412A uses a menu-driven user interface with "on-line" help -- once you learn the basics 
of operating your 9412/9412A, you may never need to refer to this manual again. 

The 9412/9412A has some unique features that are designed exclusively for use as a laser 
trigger signal generator, but can also be used as a general purpose pulse generator.  Because 
it employs a flexible microprocessor-controlled architecture, the 9412/9412A can be custom-
ized to fit your exact requirements -- contact Quantum Composers for details. 

Technical Support 

For questions or comments about operating the 9412/9412A, contact Quantum Composers via 
one of the following methods: 

Phone - (406) 582-0227 

Fax / Modem - (406) 582-0237   

Email/Internet - www.quantumcomposers.com 

Parts List 

The following parts are included with the 9412/9412A -- contact Quantum Composers if any 
parts are missing: 

9412/9412A Pulse Generator 

AC Power Cord 

User's Manual  

Quick Reference Card 

Warranty 

In addition to a 30-day money back guarantee, the 9412/9412A has a one-year limited war-
ranty from the date of delivery.  This warranty covers defects in material and workmanship.  
Quantum Composers will repair or replace any defective unit.  Contact us for information on 
obtaining warranty service. 

Summary of Contents for 9412
































Reviews: