background image

 1 

 

 

 

 

                       7080-163D 

 

 

 

       August 3, 2018

MT. VERNON E2 PELLET STOVE

MODEL(S):

MTV-E2-CSB-C

MTV-E2-PFT-C

MTV-E2-PBK-C

MTV-E2-MBK-C

MTV-E2-PDB-C

MTV-E2-PMH-C

NOTICE: DO NOT DISCARD THIS MANUAL

Owner’s Manual

Operation & Care

INSTALLER: Leave this manual with party responsible for use and operation. 

OWNER: Retain this manual for future reference. 

Contact your dealer with questions regarding installation, operation or service. 

CAUTION

Tested and approved for wood pellets only. Burning of 

any other type of fuel voids your warranty. 

NOTE

To obtain a French translation of this manual, please 

contact your dealer or visit www.quadrafire.com

00Pour obtenir une traduction française de ce manuel, 

s’il vous plaît contacter votre revendeur ou visitez www.

quadrafire.com

CAUTION

Check building codes prior to installation.

•  Installation MUST comply with local, regional, state 

and national codes and regulations.

• 

Consult local building, fire officials or authorities 

having jurisdiction about restrictions, installation 

inspection, and permits.

WARNING

Please read this entire manual before use of 

this pellet fuel-burning room heater. Failure to 

follow these instructions could result in property 

damage, bodily injury, or death. 

• 

Do not store or use gasoline or other flammable 

vapors and liquids in the vicinity of this or any other 

appliance.

• 

Do NOT burn garbage or flammable fluids such as 

gasoline, naphtha, or engine oil in room heater. 

• 

Do not over fire - If heater or chimney connector 

glows, you are over firing. Over firing will void your 

warranty.

•  Comply with all minimum clearances to combustibles 

as specified. Failure to comply may cause house fire.

HOT SURFACES! 

Glass and other surfaces are hot during 

operation AND cool down. 

WARNING

Hot glass will cause burns.

•  Do not touch glass until it is cooled

•  NEVER allow children to touch glass

•  Keep children away

•  CAREFULLY SUPERVISE children in same room as 

fireplace.

•  Alert children and adults to hazards of high 

temperatures

•  High temperatures may ignite clothing or other 

flammable materials.

•  Keep clothing, furniture, draperies and other 

flammable materials away.

f i r e - p a r t s . c o m

Summary of Contents for MT. VERNON E2 Series









































Reviews: